Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  U0167  Lost Communication with Vehicle Immobiliser Control Module  


DESCRIPTION

The transponder key computer assembly (immobiliser ECU) ensures security by controlling the START/END of the communication of matching codes with the ECM. It does so in accordance with the ignition ON/OFF status and the immobiliser SET/ UNSET status.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0167 Lost Communication with Vehicle Immobiliser Control Module Communication problem with transponder key ECU assembly (immobiliser ECU) or code mismatch
(1 trip detection logic)
·

Engine immobiliser system

·

Transponder key ECU assembly (immobiliser ECU)

·

Open or short in communication line (wire harness or connector)

·

ECM


- DTC stored

HINT:

This DTC is output when: 1) the ECM detects errors in its own communications with the transponder key ECU; 2) the ECM detects errors in the communication lines; and 3) the ECU communication IDs between the transponder key ECU and the ECM are different when an engine start is attempted.


WIRING DIAGRAM

A268106E02
0.281,3.781 0.885,3.99 0.604,0.208 10 E58 0.281,3.969 2.875,4.208 2.594,0.24 10 TRANSPONDER KEY ECU 6.208,3.781 6.813,3.99 0.604,0.208 10 E3 6.208,3.958 7.135,4.396 0.927,0.438 10 ECM 0.802,1.448 1.438,1.646 0.635,0.198 10 SIO2 0.969,2.031 1.26,2.25 0.292,0.219 10 E 1.271,1.365 1.552,1.563 0.281,0.198 10 9 1.25,1.948 1.708,2.333 0.458,0.385 10 14 6.021,1.458 6.656,1.656 0.635,0.198 10 SIO2 5.677,1.385 6.104,1.708 0.427,0.323 10 32

PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0167)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Clear the DTC.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 206

e.

Turn the ignition switch off, then turn the ignition switch to ON again.


f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine / Trouble codes.

Powertrain > Engine > Trouble Codes
50001 206

h.

Read DTCs.

Result:
Result Proceed to
U0167 A
No DTC output B
U0167 and other DTCs C


HINT:

If any transponder key ECU DTC is present, refer to its inspection procedure first.




A

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)

B

C

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
a.

Disconnect the transponder key ECU connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connections Condition Specified Conditions
E58-8 (SIO2) - E3-32 (SIO2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connections Condition Specified Conditions
E58-9 (SIO2) or E3-32 (SIO2) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the transponder key ECU connector.

Result:
Proceed to
OK
NG




OK

3.PERFORM KEY REGISTRATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM KEY REGISTRATION
a.

Clear the DTC.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 206

b.

Reregister the key (key ID code).

Result:
Proceed to
NEXT




NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Trouble codes.

Powertrain > Engine > Trouble Codes
50001 206

f.

Read DTCs.

Result:
Result Proceed to
U0167 (engine cannot start) A
No DTC output (engine start) B




A

5.REPLACE ECM

B

END

5.REPLACE ECM
a.

Replace with a new or a known-good ECM (for LHD).

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>ECM(for LHD)>REMOVAL


b.

Replace with a new or a known-good ECM (for RHD).

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>ECM(for RHD)>REMOVAL

Result:
Proceed to
NEXT




NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Trouble codes.

Powertrain > Engine > Trouble Codes
50001 206

f.

Read DTCs.

Result:
Result Proceed to
U0167 (engine cannot start) A
No DTC output (engine start) B




A

REPLACE TRANSPONDER KEY ECU ASSEMBLY

B

END