Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU (brake actuator assembly).

·

The anti-lock brake system is defective.


WIRING DIAGRAM

C248689E02
0.177,1.313 1.646,1.885 1.469,0.573 10 from IG Circuit 2.49,1.521 3.188,1.969 0.698,0.448 10 ABS 3.01,1.219 4.604,1.771 1.594,0.552 10 REVERSE CIRCUIT 2.094,1.969 2.865,2.417 0.771,0.448 10 E34 2.135,1.229 2.781,1.635 0.646,0.406 10 IG 4.573,1.229 4.844,1.604 0.271,0.375 10 - 2.094,2.146 3.667,2.938 1.573,0.792 10 COMBINATION METER ASSEMBLY 1.906,1.229 2.292,1.615 0.385,0.385 10 21 4.75,1.229 5.271,1.625 0.521,0.396 10 38 5.49,1.219 6.063,1.583 0.573,0.365 10 21 5.719,1.302 6.24,1.635 0.521,0.333 10 WA 5.719,2.385 6.333,2.781 0.615,0.396 10 GND2 5.469,2.292 5.948,2.698 0.479,0.406 10 13 5.719,2.042 6.385,2.49 0.667,0.448 10 GND1 5.542,1.958 6.01,2.354 0.469,0.396 10 1 5.729,0.406 6.323,0.865 0.594,0.458 10 +IG 5.479,0.333 5.823,0.708 0.344,0.375 10 34 2.646,0.594 3.74,1.094 1.094,0.5 10 ECU IG1 0.198,0.417 1.615,0.854 1.417,0.438 10 from IG Circuit 5.083,2.865 5.583,3.229 0.5,0.365 10 B10 5.073,3.063 7.063,3.719 1.99,0.656 10 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).



PROCEDURE

1.CHECK FOR DTC
a.

Check if DTCs for the ABS are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC not output A
DTC output B




A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.


Result:
Proceed to
OK
NG




OK

3.CHECK TERMINAL VOLTAGE (+IG TERMINAL)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (+IG TERMINAL)
a.
C248686C07
1.458,0.635 1.948,0.927 0.49,0.292 2.271,2.104 2.271,2.708 true 0.135,0.094 0.583,0.5 0.448,0.406 10 *a 1.583,0.698 2.083,1.083 0.5,0.385 10 B10 2.115,2.729 2.646,3.135 0.531,0.406 10 +IG
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B10-34 (+IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B10-1 (GND1) - Body ground Always Below 1 Ω
B10-13 (GND2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the E34 combination meter connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B10-21 (WA) - E34-18 (-) Always Below 1 Ω
B10-21 (WA) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

6.CHECK ABS WARNING LIGHT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ABS WARNING LIGHT
C248686C08
1.458,0.635 1.948,0.927 0.49,0.292 2.021,1.948 2.021,2.677 true 0.531,0.708 0.938,0.708 0.938,0.708 0.938,1.51 true 0.531,2.75 0.938,2.75 0.938,2.75 0.938,1.948 true 0.135,0.094 0.563,0.417 0.427,0.323 10 *a 1.573,0.698 2.031,1.01 0.458,0.313 10 B10 1.896,2.698 2.323,3.094 0.427,0.396 10 WA 0.094,2.667 0.885,3.052 0.792,0.385 10 GND2 0.104,0.635 0.792,0.99 0.688,0.354 10 GND1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


a.

Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Using SST, connect terminals 21 (WA) and 1 (GND1) or 13 (GND2) of the skid control ECU (brake actuator assembly) connector.


SST
09843-18040  

d.

Turn the ignition switch to ON.


e.

Check the ABS warning light.

OK:

ABS warning light turns off.


Result:
Proceed to
OK
NG




OK

NG

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)