WARNING LIGHT INITIAL CHECK
Release the parking brake.
When releasing the parking brake, set chocks to hold the vehicle for safety.
When the ignition switch is turned to ON, check that the ABS warning light and brake warning light illuminate and then turn off after 3 seconds. If a light remains on, proceed to troubleshooting for the light circuit below.
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (Using the Intelligent Tester)
If the ignition switch is turned from ON to ACC or off during test mode (signal check), DTCs stored during the sensor check will be cleared.
Procedure to enter test mode.
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in neutral and apply the parking brake.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Switch the skid control ECU (brake actuator assembly) to test mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC / Utility / Signal Check.
| Tester Display |
|---|
| Signal Check |
Check that the ABS warning light comes on for several seconds and then blinks in the test mode pattern (0.12 seconds on and 0.12 seconds off).
If the ABS warning light does not blink, inspect the ECUT terminal circuit and ABS warning light circuit.
| Trouble Area | See procedure |
|---|---|
| ECUT terminal circuit | See page ( )
|
| ABS warning light circuit (Remains on) | See page ( )
|
| ABS warning light circuit (Does not come on) | See page ( )
|
SPEED SENSOR CHECK (Using the Intelligent Tester)
The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code is stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
If the sensor check has not been completed, the ABS warning light will blink while driving and the ABS will not operate.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more over several seconds.
Check that the ABS warning light goes off.
The sensor check may not be completed if wheelspin occurs.
The ABS warning light blinks when the sensor check is completed and the vehicle stops.
The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.
Stop the vehicle.
When the sensor check is completed, the ABS warning light goes off while driving and blinks in the test mode pattern (0.12 seconds on and 0.12 seconds off) while the vehicle is stationary.
END OF SENSOR CHECK (Using the Intelligent Tester)
If the sensor check is completed, the ABS warning light blinks (0.12 seconds on and 0.12 seconds off) when the vehicle is stopped and turns off while the vehicle is being driven.
If the signal check has not been completed, the ABS warning light blinks while driving and the ABS does not operate.
READ DTC OF SENSOR CHECK FUNCTION (Using the Intelligent Tester)
Read the DTC(s) by following the intelligent tester screen.
If only DTCs other than test mode sensor check DTCs are output, repair the malfunctions and clear the DTCs.
If test mode (signal check) DTCs and other DTCs are output or if only test mode (signal check) DTCs are output, repair the malfunctions, clear the DTCs, and perform the test mode (signal check) inspection again.
Refer to the list of DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (Using SST Check Wire)
If the ignition switch is turned from ON to ACC or off during test mode (signal check), DTCs stored during the sensor check will be cleared.
Procedure to enter test mode.
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in neutral and apply the parking brake.
| *a | Front view of DLC3 |
Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.
Turn the ignition switch to ON.
Depressing the brake pedal 8 times or more within 5 seconds.
Check that the ABS warning light comes on for several seconds and then blinks in the test mode pattern (0.12 seconds on and 0.12 seconds off).
If the ABS warning light does not blink, inspect the ECUT terminal circuit and ABS warning light circuit.
| Trouble Area | See procedure |
|---|---|
| ECUT terminal circuit | See page ( )
|
| ABS warning light circuit (Remains on) | See page ( )
|
| ABS warning light circuit (Does not come on) | See page ( )
|
SPEED SENSOR CHECK (Using SST Check Wire)
The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.
After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code is stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
If the sensor check has not been completed, the ABS warning light will blink while driving and the ABS will not operate.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more over several seconds.
Check that the ABS warning light goes off.
The sensor check may not be completed if wheelspin occurs.
The ABS warning light blinks when the sensor check is completed and the vehicle stops.
The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.
Stop the vehicle.
When the sensor check is completed, the ABS warning light goes off while driving and blinks in the test mode pattern (0.12 seconds on and 0.12 seconds off) while the vehicle is stationary.
END OF SENSOR CHECK (Using SST Check Wire)
If the sensor check is completed, the ABS warning light blinks (0.12 seconds on and 0.12 seconds off) when the vehicle is stopped and turns off while the vehicle is being driven.
If the sensor check has not been completed, the ABS warning light blinks while driving and the ABS does not operate.
READ DTC OF SENSOR CHECK FUNCTION (Using SST Check Wire)
| *a | Front view of DLC3 |
Using SST, connect terminals 13 (ECUT) and 4 (E) of the DLC3.
Count the number of blinks of the ABS warning light.
If only DTCs other than test mode sensor check DTCs are output, repair the malfunctions and clear the DTCs.
If test mode (signal check) DTCs and other DTCs are output or if only test mode (signal check) DTCs are output, repair the malfunctions, clear the DTCs, and perform the test mode (signal check) inspection again.
If more than 1 malfunction is detected at the same time, the lowest numbered code is output first.
Refer to the list of DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
After performing the check, disconnect SST from terminals 4 (E) and 13 (ECUT) of the DLC3, and then turn the ignition switch off.
Turn the ignition switch to ON.
If the ignition switch is not turned to ON after SST is removed from the DLC3, the previous test mode continues.
DTC OF SENSOR CHECK FUNCTION
The codes in this table are output only in test mode (signal check).
| DTC Code | Detection Item | Trouble Area |
|---|---|---|
| C1271/81 | Low output signal of front speed sensor RH | ·
Front speed sensor ·
Speed sensor rotor RH (Front axle with ABS sensor hub and bearing assembly RH) |
| C1272/82 | Low output signal of front speed sensor LH | ·
Front speed sensor ·
Speed sensor rotor LH (Front axle with ABS sensor hub and bearing assembly LH) |
| C1273/83 | Low output signal of rear speed sensor RH | ·
Rear speed sensor RH (Rear axle hub and bearing assembly RH) ·
Sensor installation ·
Speed sensor rotor (Rear axle hub and bearing assembly RH) |
| C1274/84 | Low output signal of rear speed sensor LH | ·
Rear speed sensor LH (Rear axle hub and bearing assembly LH) ·
Sensor installation ·
Speed sensor rotor (Rear axle hub and bearing assembly LH) |
| C1275/85 | Abnormal change in output signal of front speed sensor RH | Speed sensor rotor (Front axle with ABS sensor hub and bearing assembly RH) |
| C1276/86 | Abnormal change in output signal of front speed sensor LH | Speed sensor rotor (Front axle with ABS sensor hub and bearing assembly LH) |
| C1277/87 | Abnormal change in output signal of rear speed sensor RH | Speed sensor rotor (Rear axle hub and bearing assembly RH) |
| C1278/88 | Abnormal change in output signal of rear speed sensor LH | Speed sensor rotor (Rear axle hub and bearing assembly LH) |