Home › Brake › BRAKE SYSTEM (OTHER) › K3-VE BRAKE PEDAL(for LHD) › 2011.11–2015.08
RM19Y0E _54 Brake _002993 BRAKE SYSTEM (OTHER) _0015149 K3-VE BRAKE PEDAL(for LHD) N

BRAKE SYSTEM (OTHER)  K3-VE BRAKE PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 45287 1.REMOVE LOWER STEERING COLUMN COVER

Hide 47101 2.INSPECT AND ADJUST BRAKE PEDAL

a.
C156793C01
1.313,1.5 0.677,2.25 true 1.406,1.531 1.208,2.698 true 2.219,1.625 2.51,1.542 false 0.479,2.177 1.125,2.802 0.646,0.625 10 *2 1.115,2.719 1.5,3.115 0.385,0.396 10 *3 2.552,1.458 2.979,1.885 0.427,0.427 10 *1 2.469,3.563 2.927,4.052 0.458,0.49 10 *a
*1 Stop Light Switch
*2 Push Rod
*3 Lock Nut
*a Pedal Height


Inspect the brake pedal height.

Pedal height from floor:

133.0 mm (5.236 in.)


If the pedal height is incorrect, adjust it.


b.

Adjust the brake pedal height.

i.

Disconnect the connector from the stop light switch assembly.


ii.

Turn the stop light switch counterclockwise, and remove it.


iii.

Loosen the clevis lock nut.


iv.

Adjust the pedal height by turning the pedal push rod.

Pedal height from floor:

133.0 mm (5.236 in.)



v.

Tighten the clevis lock nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


vi.
C133150C01
1.313,0.594 1.396,0.198 1.396,0.198 1.49,0.198 false 0.75,1.271 0.948,1.583 0.948,1.583 0.948,1.698 false 2.146,1.396 2.146,1.615 false 1.521,0.104 2.083,0.615 0.563,0.51 10 *1 2.052,1.635 2.542,2.083 0.49,0.448 10 *3 0.854,1.708 1.375,2.177 0.521,0.469 10 *2
*1 Adjuster
*2 Cushion
*3 Stop light switch


Insert the stop light switch assembly into the adjuster until it just touches the stop light switch cushion.

NOTICE:

Do not depress the brake pedal.



vii.
C133151C01
0.656,0.885 0.781,0.177 0.781,0.177 0.896,0.177 false 1.813,0.573 1.875,0.177 1.875,0.177 1.969,0.177 false 0.573,1.875 1,2.177 0.427,0.302 10 *a 1.979,0.094 2.406,0.49 0.427,0.396 10 *2 0.906,0.094 1.479,0.573 0.573,0.479 10 *1
*1 Shaft
*2 Stop light switch
*a 0.2 to 2.8 mm
(0.008 to 0.110 in.)


Turn the stop light switch 90° clockwise to install it.

NOTICE:

Do not depress the brake pedal.



viii.

Check the stop light switch clearance.

Stop light switch clearance:

0.2 to 2.8 mm (0.008 to 0.110 in.)



ix.

Connect the connector to the stop light switch assembly.



c.
F048932C01
2.052,1.5 2.604,1.958 0.552,0.458 10 *a
*a Pedal free play


Inspect the brake pedal free play.

i.

Stop the engine and depress the brake pedal several times until there is no vacuum left in the booster.


ii.

Push in the pedal until the beginning of the resistance is felt. Measure the distance as shown.

Pedal free play:

0.5 to 2.0 mm (0.020 to 0.079 in.)


If the brake pedal free play is not as specified, check the stop light switch clearance.



d.
R000934C01
1.792,1.75 2.25,2.177 0.458,0.427 10 *a
*a Pedal reserve distance


Inspect the brake pedal reserve distance.

i.

Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown.

Pedal reserve distance from floor:

More than 98 mm (3.9 in.) at 294 N (30 kgf, 66.1 lbf) (w/o ABS)

More than 96 mm (3.8 in.) at 294 N (30 kgf, 66.1 lbf) (w/ ABS)


If incorrect, troubleshoot the brake system.



Hide 45287 3.INSTALL LOWER STEERING COLUMN COVER