Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1544/44  Engine Revolution Signal Malfunction  C1573/73  Engine Revolution Signal Malfunction (Test Mode DTC)  


DESCRIPTION

The ECM sends engine speed signals to the power steering ECU assembly.

DTC No. Detection Item Trouble Area Warning Indicate Return-to-normal Condition
C1544/44 Engine Revolution Signal Malfunction
·

Open or short in engine speed signal circuit

·

Crankshaft position sensor

·

ECM

·

Power steering ECU assembly

·

Wire harness and connector


Comes on Ignition switch ON again
C1573/73 Engine Revolution Signal Malfunction (Test Mode DTC)
·

Open or short in engine speed signal circuit

·

Crankshaft position sensor

·

ECM

·

Power steering ECU assembly

·

Wire harness and connector


Comes on -

WIRING DIAGRAM

C248675E04
4.354,2.208 6.802,2.531 2.448,0.323 10 POWER STEERING ECU ASSEMBLY 4.917,0.99 5.115,1.167 0.198,0.177 10 12 0.656,2.208 2.99,2.531 2.333,0.323 10 COMBINATION METER ASSEMBLY 1.573,1.094 1.906,1.26 0.333,0.167 10 REV 5.146,1.083 5.479,1.229 0.333,0.146 10 REV 0.667,2.031 1,2.177 0.333,0.146 10 E34 4.365,2.052 4.698,2.198 0.333,0.146 10 E27 1.958,0.99 2.146,1.167 0.188,0.177 10 10

PROCEDURE

1.PERFORM SIGNAL CHECK (ENGINE SPEED SIGNAL)
a.

Perform the signal check in the Test Mode procedure.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TEST MODE PROCEDURE

OK:

Test mode DTC C1573 is cleared.


Result:
Result Proceed to
NG A
OK B




A

2.CHECK FOR DTC (ENGINE CONTROL SYSTEM)

B

2.CHECK FOR DTC (ENGINE CONTROL SYSTEM)
a.

Check whether DTCs for the ECM are output.

Powertrain > Engine > Trouble Codes
50001 206
OK:

DTCs for ECM are not output.


Result:
Result Proceed to
OK A
NG (for 3SZ-VE) B
NG (for K3-VE) C




A

3.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

B

C

3.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester or Techstream on.


d.

Enter the following menus: Chassis / EMPS/ Data List / Engine Revolution.

Chassis > EMPS > Data List
Tester Display
Engine Revolution
50003 317 4

e.

Start the engine.


f.

Read the value displayed on the tester or Techstream.

OK:

Engine speeds displayed on tester and tachometer display are equal.


Result:
Result Proceed to
NG A
OK B




A

4.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING ECU)

B

4.CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING ECU)
a.

Disconnect the E34 ECM connector.


b.

Disconnect the E27 power steering ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E34-10 (REV) - E27-12 (REV) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E27-12 (REV) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

5.INSPECT ECM (REV SIGNAL WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (REV SIGNAL WAVEFORM)
a.

Reconnect the E34 ECM connector.


b.

Reconnect the E27 power steering ECU connector.


c.
C249061C02
1.781,0.771 2.156,1.021 0.375,0.25 1.823,1.375 1.74,1.833 true 0.156,0.073 0.823,0.563 0.667,0.49 10 *a 1.427,1.865 2.677,2.354 1.25,0.49 10 12 (REV) 2.51,2.448 3.271,2.917 0.76,0.469 10 5 V/DIV . 2.604,3.396 3.208,3.854 0.604,0.458 10 GND 1.031,4.198 2.375,4.552 1.344,0.354 10 10 ms ./DIV . 1.833,0.823 2.469,1.229 0.635,0.406 10 E27
*a Component with harness connected
(Power Steering ECU)


Check the input waveform.

i.

Connect an oscilloscope to terminals E27-12 (REV) and body ground.


ii.

Turn the ignition switch to ON.


iii.

Start the engine.


iv.

Check the signal waveform according to the condition(s) in the table below.

Terminal E27-12 (REV) - Body ground
Tool setting 5 V/DIV ., 10 ms./DIV .
Vehicle condition Idling

OK:

The waveform is displayed as shown in the illustration.


Result:
Result Proceed to
OK A
NG (for 3SZ-VE) B
NG (for K3-VE) C





A

REPLACE POWER STEERING ECU

B

C