Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2011.11–2015.08
RM19Y0E _55 Steering _002997 POWER ASSIST SYSTEMS _0015160 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TEST MODE PROCEDURE  


NOTICE:

The test mode inspection is conducted after the power steering ECU has been replaced with a new one.


HINT:
·

Speed sensor signals can be checked easily in test mode.

·

Test mode codes C1571 and C1573 are stored during transition to test mode. These codes do not indicate a malfunction since the codes will be cleared when the ECU determines that the sensor is normal.

·

The test mode codes are cleared simultaneously when test mode is terminated.



ENTER TEST MODE


a.

When using an intelligent tester or Techstream;

i.

Turn the ignition switch off.


ii.

Connect the intelligent tester or Techstream to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the tester or Techstream on.


v.

Switch the power steering ECU to the Test Mode. Enter the following menus: Chassis / EMPS / Utility / Signal Check.



b.
C193959C07
1.031,1.854 1.146,1.854 1.146,1.854 1.375,1.083 true 2.094,0.396 1.896,0.396 1.896,0.396 1.583,0.906 true 0.042,0.021 0.302,0.24 0.26,0.219 10 *a 0.375,1.781 0.979,1.958 0.604,0.177 10 EPS TS 2.146,0.323 2.375,0.521 0.229,0.198 10 E
*a Front view of DLC3


When not using an intelligent tester or Techstream;

i.

Turn the ignition switch off.


ii.

Using SST Connect terminals 3 (EPS TS) and 4 (E) of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.

HINT:
·

Be sure to connect the correct terminals of the connector, otherwise a malfunction may occur.

·

If the torque sensor zero point calibration has not been performed, the torque sensor zero point calibration is performed automatically when test mode is entered.






CHECK TEST MODE DISPLAY


a.
F102335E01
0.052,0.125 3.219,0.333 3.167,0.208 10 Power Steering Warning Light Test Mode Pattern 0.208,0.74 1.281,0.958 1.073,0.219 10 0.125 seconds 2.031,0.75 3.042,0.927 1.01,0.177 10 0.125 seconds 0.406,1.073 0.719,1.271 0.313,0.198 10 On 0.406,1.396 0.865,1.594 0.458,0.198 10 Off 1.698,1.677 2.615,1.875 0.917,0.198 10 (4 Hz)

The EPS warning light blinks as shown in the illustration when test mode is entered.



CHECK VEHICLE SPEED SIGNAL AND ENGINE SPEED SIGNAL


a.

Drive the vehicle until the vehicle speed reaches 20 km/h (12 mph) or more.

C229852E03
0.271,0.156 2.083,0.417 1.813,0.26 10 When system is normal: 1.927,0.542 2.865,0.75 0.938,0.208 10 km/h (mph) 0.552,1.344 1.635,1.521 1.083,0.177 10 Vehicle speed 2.021,1.094 2.51,1.281 0.49,0.188 10 20 (12) 3.427,1.302 4.104,1.448 0.677,0.146 10 2 seconds 2.271,1.667 2.573,1.833 0.302,0.167 10 0 0.5,2.438 1.698,2.781 1.198,0.344 10 EPS warning light 1.802,2.313 2.177,2.469 0.375,0.156 10 ON 1.802,2.594 2.219,2.76 0.417,0.167 10 OFF 2.323,2.792 3.115,3.01 0.792,0.219 10 4 Hz blink 3.229,2.792 7.094,3.125 3.865,0.333 10 Light blinks until test mode code C1571 and C1573 is cleared. 6.052,1.656 6.646,1.844 0.594,0.188 10 Time 3.229,3.094 6.917,3.542 3.688,0.448 10 Light goes off when driving at 20 km/h (12 mph) or more for 2 seconds or more.



READ TEST MODE CODE


Test Mode Code
Code Detection Item Condition to Clear Code Trouble Area
C1571
((Click here))
Vehicle speed signal Vehicle speed at 20 km/h (12 mph) or more for 2 seconds or more If the code cannot be cleared, any of the following areas may be malfunctioning:
·

Vehicle speed signal circuit

·

Combination meter assembly

·

Instrument panel junction block assembly

·

Power steering ECU assembly


C1573
((Click here))
Engine speed signal Engine speed at 387 rpm or more for 2 second or more If the code cannot be cleared, any of the following areas may be malfunctioning:
·

Engine speed signal circuit

·

Power steering ECU assembly

·

ECM



a.

When using an intelligent tester or Techstream;

i.

Check the DTCs in test mode.

NOTICE:

Test mode codes are cleared when test mode is terminated.




b.
C193959C08
1.031,1.854 1.146,1.854 1.146,1.854 1.375,1.083 true 2.083,0.385 1.885,0.385 1.885,0.385 1.573,0.896 true 0.042,0.021 0.323,0.198 0.281,0.177 10 *a 0.375,1.781 1,1.927 0.625,0.146 10 EPS TS 2.146,0.323 2.354,0.5 0.208,0.177 10 E
*a Front view of DLC3


When not using an intelligent tester or Techstream;

i.

Turn the ignition switch off.


ii.

Connect terminals 3 (EPS TS) and 4 (E) of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.
C230060E03
0.156,0.698 0.656,0.917 0.5,0.219 10 0.25 1.635,0.448 3.177,0.656 1.542,0.208 10 Normal Code (4Hz blink) 0.302,1.396 0.563,1.604 0.26,0.208 10 2 0.813,1.302 1.281,1.51 0.469,0.208 10 0.25 2.521,2.75 3.167,2.979 0.646,0.229 10 (Seconds) 1.573,1.313 2.969,1.531 1.396,0.219 10 Codes 11 and 23 0.292,2.208 0.552,2.427 0.26,0.219 10 4 0.604,2.208 1.021,2.417 0.417,0.208 10 1.5 1.094,2.208 1.448,2.417 0.354,0.208 10 2.5 1.979,2.219 2.354,2.438 0.375,0.219 10 0.5 2.208,2.219 2.583,2.438 0.375,0.219 10 0.5

Read the number of times that the EPS warning light on the combination meter blinks.

·

To indicate the normal code, the EPS warning light comes on for 0.25 seconds at intervals of 0.25 seconds (4Hz blink).

·

When outputting a DTC, the EPS warning light displays it at intervals of 4 seconds. When outputting two or more DTCs, the EPS warning light displays each DTC at intervals 2.5 seconds, and repeats from the first one 4 seconds after indicating the last one.

·

If two or more malfunctions are detected at the same time, DTCs are displayed in ascending numerical order.





END OF TEST MODE


a.

When using an intelligent tester or Techstream;

i.

Return to normal mode by following the instructions on the tester screen.


ii.

Turn the ignition switch off and disconnect the tester or Techstream.



b.

When not using an intelligent tester or Techstream;

i.

Turn the ignition switch off and disconnect terminals 3 (EPS TS) and 4 (E) of the DLC3.

SST
09843-18040  


ii.

Turn the ignition switch to ON.