Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › 2011.11–2015.08
RM19Y0E _56 Audio / Visual / Telematics _003000 AUDIO / VIDEO _0015166 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the stereo component tuner assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E234125E02
5.365,3.917 6.896,4.573 1.531,0.656 10 STEREO JACK ADAPTER ASSEMBLY 0.542,3.927 2.188,4.583 1.646,0.656 10 STEREO COMPONENT TUNER ASSEMBLY 5.698,1.479 6.125,1.646 0.427,0.167 10 UDO- 5.698,2.083 6.188,2.25 0.49,0.167 10 UDO+ 5.698,2.667 6.177,2.833 0.479,0.167 10 UJSG 5.479,1.396 5.656,1.563 0.177,0.167 10 2 5.698,0.885 6.229,1.052 0.531,0.167 10 UPI 1.281,1.49 1.656,1.656 0.375,0.167 10 UDI- 1.281,2.083 1.667,2.25 0.385,0.167 10 UDI+ 1.188,2.677 1.667,2.844 0.479,0.167 10 UESG 1.271,0.917 1.667,1.083 0.396,0.167 10 UPO 5.479,0.813 5.656,0.979 0.177,0.167 10 1 5.479,2 5.656,2.167 0.177,0.167 10 3 5.479,2.594 5.656,2.76 0.177,0.167 10 4 0.531,3.74 0.896,3.906 0.365,0.167 10 E53 5.365,3.74 5.729,3.906 0.365,0.167 10 E52 1.74,1.406 1.917,1.573 0.177,0.167 10 2 1.74,0.813 1.917,0.979 0.177,0.167 10 1 1.74,1.99 1.917,2.156 0.177,0.167 10 3 1.74,2.583 1.917,2.75 0.177,0.167 10 4

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to before play begins.

·

When using a USB device, files that are copy protected or encrypted cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION


Result:
Result Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B




A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER - STEREO JACK ADAPTER)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER - STEREO JACK ADAPTER)
a.

Remove the stereo component tuner assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Remove the stereo jack adapter assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO JACK ADAPTER ASSEMBLY>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E52-1 (UPI) - E53-1 (UPO) Always Below 1 Ω
E52-2 (UDO-) - E53-2 (UD1-) Always Below 1 Ω
E52-3 (UDO+) - E53-3 (UD1+) Always Below 1 Ω
E52-4 (UJSG) - E53-4 (UESG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E52-1 (UPI) - Body ground Always 10 kΩ or higher
E52-2 (UDO-) - Body ground Always 10 kΩ or higher
E52-3 (UDO+) - Body ground Always 10 kΩ or higher
E52-4 (UJSG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

3.INSPECT STEREO COMPONENT TUNER ASSEMBLY (STEREO JACK ADAPTER POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT TUNER ASSEMBLY (STEREO JACK ADAPTER POWER SOURCE)
a.
E234124C04
1.51,0.375 1.969,0.656 0.458,0.281 1.385,1.198 0.979,1.198 true 2.5,1.188 2.083,1.188 true 0.135,0.094 0.333,0.281 0.198,0.188 10 *a 1.604,0.438 1.896,0.594 0.292,0.156 10 E52 0.698,1.135 0.99,1.292 0.292,0.156 10 UPI 2.563,1.104 2.969,1.302 0.406,0.198 10 UJSG
*a Front view of wire harness connector
(to Stereo Jack Adapter Assembly)


Install the stereo component tuner assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>INSTALLATION


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E52-1 (UPI) - E52-4 (UJSG) Ignition switch ACC 5 V


Result:
Proceed to
OK
NG




OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE STEREO COMPONENT TUNER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/ restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Make sure that back up music data is available before performing this operation.


OK:

Malfunction disappears.


Result:
Proceed to
OK
NG




OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION



Result:
Proceed to
NEXT




NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if USB device or "iPod" is recognized by the stereo component tuner assembly, or if information such as track, artist and album names are displayed on screen.

OK:

Malfunction disappears.


Result:
Proceed to
OK
NG




OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG