Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (+B) or 14 (CANL) and 16 (+B) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (+B) or 14 (CANL) and 16 (+B) of DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

ECM

·

TCM*1

·

Combination meter assembly*2

·

CAN No. 1 junction connector



*1 : for A/T

*2 : w/ Multi Information Display

WIRING DIAGRAM

C243550E06
0.063,0.052 1.854,1.031 1.792,0.979 12 w/ Multi Information Display : 0.208,5.604 1.083,6.063 0.875,0.458 10 * : for A/T 5.521,1.833 6.021,2.24 0.5,0.406 10 DLC3 2.01,0.229 2.458,0.604 0.448,0.375 10 ECM 0.979,3.052 2.552,3.854 1.573,0.802 10 CAN NO. 1 JUNCTION CONNECTOR 4.385,5.125 5.813,5.885 1.427,0.76 10 COMBINATION METER ASSEMBLY 2.552,1.656 3.156,2.021 0.604,0.365 10 CANL 5.5,1.354 6.104,1.76 0.604,0.406 10 CANL 3.802,1.656 4.427,2.073 0.625,0.417 10 CANH 2.521,4.948 3.167,5.385 0.646,0.438 10 CANL 3.802,4.948 4.417,5.365 0.615,0.417 10 CANH 5.417,1.094 6.104,1.542 0.688,0.448 10 CANH 5.552,3.552 6.208,3.927 0.656,0.375 10 CANL 5.531,2.979 6.125,3.417 0.594,0.438 10 CANH 3.875,0.99 4.5,1.385 0.625,0.396 10 HCAN 3.865,1.438 4.417,1.792 0.552,0.354 10 LCAN 3.177,5.51 3.833,5.969 0.656,0.458 10 120 Ω 3.167,0.125 3.74,0.479 0.573,0.354 10 120 Ω 2.844,1.885 3.188,2.229 0.344,0.344 10 3 3.813,1.896 4.156,2.271 0.344,0.375 10 4 2.76,2.615 3.198,2.979 0.438,0.365 10 10 4.865,1.531 5.25,1.875 0.385,0.344 10 W 4.865,0.896 5.229,1.271 0.365,0.375 10 B 4.813,3.646 5.281,4 0.469,0.354 10 LG 4.844,2.896 5.229,3.208 0.385,0.313 10 P 3.802,2.604 4.146,2.958 0.344,0.354 10 8 2.75,2.271 3.115,2.573 0.365,0.302 10 G 3.823,2.302 4.146,2.625 0.323,0.323 10 R 2.74,4.354 3.167,4.688 0.427,0.333 10 W 3.833,4.375 4.24,4.75 0.406,0.375 10 B 2.813,4.042 3.26,4.417 0.448,0.375 10 3 3.823,4.042 4.167,4.385 0.344,0.344 10 1 2.76,4.698 3.188,5.115 0.427,0.417 10 29 3.813,4.698 4.281,5.104 0.469,0.406 10 28 5.115,0.969 5.51,1.354 0.396,0.385 10 6 5.188,1.458 5.573,1.792 0.385,0.333 10 14 4.302,2.948 4.677,3.302 0.375,0.354 10 9 4.292,3.542 4.635,3.885 0.344,0.344 10 11 5.354,2.969 5.76,3.344 0.406,0.375 10 7 5.302,3.583 5.656,3.948 0.354,0.365 10 17 4.375,0.99 4.719,1.313 0.344,0.323 10 2 4.375,1.448 4.719,1.833 0.344,0.385 10 1 4.375,4.938 4.906,5.302 0.531,0.365 10 E34 2.01,0.073 2.49,0.417 0.479,0.344 10 E3 0.969,2.854 1.552,3.24 0.583,0.385 10 E45 5.521,1.656 6.073,1.948 0.552,0.292 10 E12 0.875,5.958 2.771,6.438 1.896,0.479 10 : CAN Main Bus Line (CANH) 0.875,6.333 2.844,6.708 1.969,0.375 10 : CAN Main Bus Line (CANL) 4.208,5.948 6.365,6.448 2.156,0.5 10 : CAN Branch Bus Line (CANH) 4.208,6.313 6.333,6.813 2.125,0.5 10 : CAN Branch Bus Line (CANL) 5.5,3.813 6.031,4.167 0.531,0.354 10 E9 5.5,3.979 6.135,4.417 0.635,0.438 10 TCM*

C243557E08
0.094,0.094 1.688,0.865 1.594,0.771 12 w/o Multi Information Display : 5.521,1.875 6.135,2.344 0.615,0.469 10 DLC3 2.021,0.26 2.51,0.646 0.49,0.385 10 ECM 2.552,1.667 3.188,2.031 0.635,0.365 10 CANL 5.51,1.354 6.125,1.813 0.615,0.458 10 CANL 3.813,1.667 4.49,2.021 0.677,0.354 10 CANH 2.531,3.031 3.094,3.406 0.563,0.375 10 CANL 3.813,3.021 4.438,3.396 0.625,0.375 10 CANH 5.427,1.094 6.135,1.458 0.708,0.365 10 CANH 3.875,0.979 4.458,1.354 0.583,0.375 10 HCAN 3.875,1.458 4.5,1.813 0.625,0.354 10 LCAN 3.188,3.604 3.813,4.052 0.625,0.448 10 120 Ω 3.177,0.135 3.74,0.521 0.563,0.385 10 120 Ω 2.823,1.906 3.24,2.271 0.417,0.365 10 3 3.823,1.906 4.177,2.229 0.354,0.323 10 4 4.875,1.552 5.198,1.927 0.323,0.375 10 W 4.885,0.885 5.24,1.24 0.354,0.354 10 B 2.75,2.281 3.125,2.656 0.375,0.375 10 G 3.844,2.302 4.24,2.677 0.396,0.375 10 R 5.125,1 5.479,1.354 0.354,0.354 10 6 5.198,1.469 5.615,1.844 0.417,0.375 10 14 4.385,0.979 4.708,1.292 0.323,0.313 10 2 4.396,1.479 4.74,1.823 0.344,0.344 10 1 2.021,0.083 2.458,0.427 0.438,0.344 10 E3 5.521,1.688 6.094,2.01 0.573,0.323 10 E12 0.875,4.031 2.781,4.448 1.906,0.417 10 : CAN Main Bus Line (CANH) 0.885,4.406 2.792,4.792 1.906,0.385 10 : CAN Main Bus Line (CANL) 4.219,4.021 6.292,4.406 2.073,0.385 10 : CAN Branch Bus Line (CANH) 4.208,4.396 6.188,4.75 1.979,0.354 10 : CAN Branch Bus Line (CANL) 3.823,2.781 4.208,3.125 0.385,0.344 10 7 2.75,2.771 3.125,3.125 0.375,0.354 10 17 4.385,3.031 4.875,3.365 0.49,0.333 10 E9 4.385,3.219 4.917,3.615 0.531,0.396 10 TCM* 0.271,3.521 1.177,3.979 0.906,0.458 10 * : for A/T

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>Check CAN Bus Line for Short to +B).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 5 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the E3 ECM connector.


c.
E231257C03
1.448,0.26 1.938,0.552 0.49,0.292 2.26,0.469 2.01,0.927 true 1.896,1.479 1.646,1.927 true 0.104,0.094 0.479,0.417 0.375,0.323 10 *a 2.302,0.365 2.875,0.688 0.573,0.323 10 CANH 1.24,1.854 1.74,2.167 0.5,0.313 10 CANL 1.542,0.323 2.042,0.688 0.5,0.365 10 E12
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher


Result:
proceed to
OK
NG




OK

2.SYSTEM CHECK

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.SYSTEM CHECK
a.

Check the vehicle specifications.

Result:
Result Proceed to
for A/T
w/ Multi Information Display
A
for M/T
w/ Multi Information Display
B
for A/T
w/o Multi Information Display




A

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)

B

4.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU)
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the E3 ECM connector.


b.
C243556C01
0.271,0.729 0.76,1.021 0.49,0.292 0.271,2.542 0.76,2.833 0.49,0.292 2.271,1.042 2.615,1.5 true 2.615,0.281 2.271,0.74 true 1.49,0.281 1.833,0.74 true 2.094,1.031 2.635,1.76 true 1.656,1.063 1.313,1.51 true 1.823,1.052 1.271,1.781 true 2.156,2.865 1.938,3.208 true 0.094,0.052 0.469,0.385 0.375,0.333 10 *a 2.635,0.177 2.969,0.5 0.333,0.323 10 *c 1.323,0.156 1.635,0.469 0.313,0.313 10 *c 2.656,1.438 2.99,1.75 0.333,0.313 10 *d 2.656,1.719 2.979,2 0.323,0.281 10 *e 1.115,1.74 1.417,2.01 0.302,0.271 10 *d 1.125,1.448 1.427,1.75 0.302,0.302 10 *e 0.365,0.781 0.813,1.115 0.448,0.333 10 E45 0.125,1.979 0.5,2.292 0.375,0.313 10 *b 1.719,3.146 2.021,3.427 0.302,0.281 10 +B 0.344,2.604 0.823,2.917 0.479,0.313 10 E12
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b Front view of DLC3
*c to Combination Meter Assembly
*d to ECM
*e to TCM


Disconnect the E45 CAN No. 1 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E45-1 - E12-16 (+B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
E45-3 - E12-16 (+B)
E45-8 - E12-16 (+B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
E45-10 - E12-16 (+B)
E45-9 - E12-16 (+B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher TCM
E45-11 - E12-16 (+B)


Result:
Result Proceed to
OK A
NG (Combination meter assembly main line) B
NG (ECM main line) C
NG (TCM branch line) D




A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - ECM)

D

4.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU)
4.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU)
a.

Reconnect the E45 CAN No. 1 junction connector.


b.

Disconnect the ECU connected to the CAN bus line that is shorted to +B.

HINT:

If the ECU has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU that is connected to the shorted bus line, refer to the terminals of ECU tables.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU



c.
E231257C04
1.448,0.26 1.938,0.552 0.49,0.292 2.385,1.469 2.635,1.917 true 2.26,0.469 2.01,0.927 true 1.906,1.49 1.656,1.938 true 0.104,0.094 0.49,0.438 0.385,0.344 10 *a 2.292,0.354 2.885,0.708 0.594,0.354 10 CANH 2.698,1.865 3.042,2.156 0.344,0.292 10 +B 1.25,1.865 1.719,2.167 0.469,0.302 10 CANL 1.542,0.323 2.042,0.604 0.5,0.281 10 E12
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-16 (+B) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
E12-14 (CANL) - E12-16 (+B)


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU, there may be a short in the ECU.


Result:
proceed to
OK
NG




OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU WIRE OR CONNECTOR