Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.11–2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (E) or 14 (CANL) and 4 (E) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 4 (E) or 14 (CANL) and 4 (E) of DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

ECM

·

TCM*1

·

Combination meter assembly*2

·

CAN No. 1 junction connector



*1 : for A/T

*2 : w/ Multi Information Display

WIRING DIAGRAM

C243550E07
0.083,0.094 1.76,0.917 1.677,0.823 12 w/ Multi Information Display : 0.208,5.604 1.177,6.031 0.969,0.427 10 * : for A/T 5.521,1.833 6.125,2.323 0.604,0.49 10 DLC3 2.01,0.271 2.448,0.635 0.438,0.365 10 ECM 0.969,3.021 2.448,3.667 1.479,0.646 10 CAN NO. 1 JUNCTION CONNECTOR 4.385,5.115 5.813,6.094 1.427,0.979 10 COMBINATION METER ASSEMBLY 2.542,1.656 3.094,2 0.552,0.344 10 CANL 5.469,1.354 6.01,1.677 0.542,0.323 10 CANL 3.802,1.677 4.375,2.052 0.573,0.375 10 CANH 2.521,4.938 3.104,5.313 0.583,0.375 10 CANL 3.802,4.969 4.448,5.417 0.646,0.448 10 CANH 5.417,1.083 6.073,1.49 0.656,0.406 10 CANH 5.563,3.573 6.146,3.938 0.583,0.365 10 CANL 5.531,2.979 6.167,3.375 0.635,0.396 10 CANH 3.875,0.969 4.448,1.365 0.573,0.396 10 HCAN 3.875,1.458 4.438,1.833 0.563,0.375 10 LCAN 3.177,5.521 3.771,5.927 0.594,0.406 10 120 Ω 3.167,0.125 3.708,0.51 0.542,0.385 10 120 Ω 2.844,1.896 3.188,2.26 0.344,0.365 10 3 3.802,1.885 4.177,2.24 0.375,0.354 10 4 2.75,2.604 3.135,2.969 0.385,0.365 10 10 4.865,1.542 5.219,1.927 0.354,0.385 10 W 4.875,0.906 5.219,1.25 0.344,0.344 10 B 4.802,3.625 5.198,4 0.396,0.375 10 LG 4.844,2.906 5.167,3.271 0.323,0.365 10 P 3.813,2.615 4.198,2.948 0.385,0.333 10 8 2.74,2.302 3.135,2.635 0.396,0.333 10 G 3.833,2.292 4.177,2.635 0.344,0.344 10 R 2.74,4.365 3.177,4.698 0.438,0.333 10 W 3.833,4.365 4.24,4.771 0.406,0.406 10 B 2.844,4.042 3.198,4.427 0.354,0.385 10 3 3.823,4.031 4.229,4.396 0.406,0.365 10 1 2.76,4.708 3.198,5.063 0.438,0.354 10 29 3.823,4.698 4.281,5.083 0.458,0.385 10 28 5.115,0.969 5.469,1.313 0.354,0.344 10 6 5.188,1.469 5.5,1.76 0.313,0.292 10 14 4.302,2.979 4.677,3.333 0.375,0.354 10 9 4.292,3.583 4.656,3.938 0.365,0.354 10 11 5.344,2.99 5.729,3.365 0.385,0.375 10 7 5.292,3.583 5.74,3.958 0.448,0.375 10 17 4.375,0.99 4.729,1.354 0.354,0.365 10 2 4.365,1.469 4.708,1.875 0.344,0.406 10 1 4.375,4.927 4.76,5.302 0.385,0.375 10 E34 2.01,0.094 2.458,0.417 0.448,0.323 10 E3 0.969,2.833 1.583,3.24 0.615,0.406 10 E45 5.521,1.698 6.063,2.083 0.542,0.385 10 E12 0.896,5.948 2.823,6.406 1.927,0.458 10 : CAN Main Bus Line (CANH) 0.875,6.323 2.833,6.76 1.958,0.438 10 : CAN Main Bus Line (CANL) 4.219,5.938 6.302,6.427 2.083,0.49 10 : CAN Branch Bus Line (CANH) 4.229,6.313 6.26,6.719 2.031,0.406 10 : CAN Branch Bus Line (CANL) 5.5,3.823 6,4.146 0.5,0.323 10 E9 5.5,4.01 6.104,4.479 0.604,0.469 10 TCM*

C243557E09
0.063,0.125 1.656,0.896 1.594,0.771 12 w/o Multi Information Display : 5.521,1.885 6.042,2.292 0.521,0.406 10 DLC3 2.021,0.281 2.573,0.677 0.552,0.396 10 ECM 2.542,1.688 3.135,2.052 0.594,0.365 10 CANL 5.51,1.375 6.104,1.729 0.594,0.354 10 CANL 3.813,1.667 4.375,2.031 0.563,0.365 10 CANH 2.531,3.01 3.229,3.375 0.698,0.365 10 CANL 3.813,3.021 4.469,3.396 0.656,0.375 10 CANH 5.427,1.115 6.104,1.479 0.677,0.365 10 CANH 3.875,1.01 4.448,1.385 0.573,0.375 10 HCAN 3.875,1.469 4.438,1.885 0.563,0.417 10 LCAN 3.188,3.604 3.813,3.99 0.625,0.385 10 120 Ω 3.177,0.135 3.76,0.448 0.583,0.313 10 120 Ω 2.813,1.917 3.219,2.313 0.406,0.396 10 3 3.823,1.896 4.167,2.25 0.344,0.354 10 4 4.875,1.552 5.229,1.885 0.354,0.333 10 W 4.885,0.927 5.26,1.24 0.375,0.313 10 B 2.75,2.281 3.177,2.594 0.427,0.313 10 G 3.844,2.302 4.281,2.656 0.438,0.354 10 R 5.125,1.01 5.438,1.333 0.313,0.323 10 6 5.198,1.469 5.542,1.813 0.344,0.344 10 14 4.396,1 4.74,1.302 0.344,0.302 10 2 4.385,1.448 4.781,1.802 0.396,0.354 10 1 2.021,0.115 2.521,0.448 0.5,0.333 10 E3 5.521,1.729 6.083,2.083 0.563,0.354 10 E12 0.885,4.031 2.729,4.427 1.844,0.396 10 : CAN Main Bus Line (CANH) 0.885,4.406 2.802,4.771 1.917,0.365 10 : CAN Main Bus Line (CANL) 4.208,4 6.25,4.406 2.042,0.406 10 : CAN Branch Bus Line (CANH) 4.208,4.385 6.208,4.75 2,0.365 10 : CAN Branch Bus Line (CANL) 3.823,2.802 4.198,3.156 0.375,0.354 10 7 2.75,2.792 3.094,3.135 0.344,0.344 10 17 4.385,3.021 4.917,3.323 0.531,0.302 10 E9 4.385,3.177 4.917,3.573 0.531,0.396 10 TCM* 0.271,3.542 1.146,4.052 0.875,0.51 10 * : for A/T

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>Check CAN Bus Line for Short to GND).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 5 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the E3 ECM connector.


c.
E231257C05
1.448,0.26 1.938,0.552 0.49,0.292 2.26,0.469 2.01,0.927 true 1.906,1.49 1.656,1.938 true 0.104,0.094 0.479,0.438 0.375,0.344 10 *a 2.323,0.385 2.875,0.729 0.552,0.344 10 CANH 1.177,1.865 1.646,2.177 0.469,0.313 10 CANL 1.542,0.323 2.042,0.667 0.5,0.344 10 E12
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher


Result:
proceed to
OK
NG




OK

2.SYSTEM CHECK

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.SYSTEM CHECK
a.

Check the vehicle specifications.

Result:
Result Proceed to
for A/T
w/ Multi Information Display
A
for M/T
w/ Multi Information Display
B
for A/T
w/o Multi Information Display




A

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)

B

4.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU)
3.CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN NO. 1 JUNCTION CONNECTOR)
a.

Reconnect the E3 ECM connector.


b.
C243556C02
0.271,0.646 0.76,0.938 0.49,0.292 0.271,2.458 0.76,2.75 0.49,0.292 2.271,1.042 2.615,1.5 true 2.604,0.292 2.26,0.75 true 1.49,0.281 1.833,0.74 true 2.094,1.063 2.635,1.792 true 1.635,1.052 1.292,1.5 true 1.813,1.073 1.26,1.802 true 1.604,2.427 1.448,2.146 true 0.094,0.073 0.448,0.354 0.354,0.281 10 *a 2.604,0.177 2.885,0.479 0.281,0.302 10 *c 1.333,0.167 1.74,0.49 0.406,0.323 10 *c 2.635,1.438 2.948,1.729 0.313,0.292 10 *d 2.646,1.729 2.979,2.021 0.333,0.292 10 *e 1.115,1.729 1.448,2.042 0.333,0.313 10 *d 1.146,1.417 1.458,1.771 0.313,0.354 10 *e 0.365,0.698 0.813,1.094 0.448,0.396 10 E45 0.125,1.896 0.438,2.198 0.313,0.302 10 *b 1.344,2.01 1.677,2.333 0.333,0.323 10 E 0.344,2.521 0.823,2.917 0.479,0.396 10 E12
*a Rear view of wire harness connector
(to CAN No. 1 Junction Connector)
*b Front view of DLC3
*c to Combination Meter Assembly
*d to ECM
*e to TCM


Disconnect the E45 CAN No. 1 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
E45-1 - E12-4 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
E45-3 - E12-4 (E)
E45-8 - E12-4 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
E45-10 - E12-4 (E)
E45-9 - E12-4 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher TCM
E45-11 - E12-4 (E)


Result:
Result Proceed to
OK A
NG (Combination meter assembly main line) B
NG (ECM main line) C
NG (TCM branch line) D




A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 JUNCTION CONNECTOR - ECM)

D

4.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU)
4.CHECK FOR SHORT TO GND IN CONNECTED COMPONENT (ECU)
a.

Reconnect the E45 CAN No. 1 junction connector.


b.

Disconnect the ECU connected to the CAN bus line that is shorted to ground.

HINT:

If the ECU has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU that is connected to the shorted bus line, refer to the terminals of ECU tables.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU



c.
E231257C06
1.448,0.26 1.938,0.552 0.49,0.292 2.25,0.469 2,0.927 true 1.302,0.469 1.552,0.927 true 1.906,1.49 1.635,1.906 true 0.104,0.094 0.469,0.448 0.365,0.354 10 *a 2.292,0.344 2.844,0.656 0.552,0.313 10 CANH 1.156,0.354 1.49,0.646 0.333,0.292 10 E 1.281,1.854 1.833,2.125 0.552,0.271 10 CANL 1.542,0.323 2.031,0.656 0.49,0.333 10 E12
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E12-6 (CANH) - E12-4 (E) Cable disconnected from negative (-) battery terminal 200 Ω or higher
E12-14 (CANL) - E12-4 (E)


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU, there may be a short in the ECU.


Result:
proceed to
OK
NG




OK

REPLACE CORRESPONDING ECU

NG

REPAIR OR REPLACE CORRESPONDING ECU WIRE OR CONNECTOR