Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003006 THEFT DETERRENT / KEYLESS ENTRY _0015192 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

When the engine immobiliser system is set, the security indicator light blinks continuously, but does not illuminate if the engine immobiliser system is not set.

WIRING DIAGRAM

B298497E02
3.219,1.885 3.688,2.219 0.469,0.333 10 IMO 3.781,1.885 4.219,2.198 0.438,0.313 10 IND 2.385,0.99 3.281,1.406 0.896,0.417 10 ECU IG2 2.344,0.51 3.271,0.875 0.927,0.365 10 BACK UP 3.51,0.823 5.104,1.708 1.594,0.885 10 from Ignition or Starter Switch Assembly 3.51,0.344 4.708,0.823 1.198,0.479 10 from Battery 2.583,3.396 5.021,3.802 2.438,0.406 10 *2: w/ Wireless Door Lock System 0.094,3.396 2.927,3.802 2.833,0.406 10 *1: w/o Wireless Door Lock System 0.344,2.938 3.396,3.365 3.052,0.427 10 TRANSPONDER KEY ECU ASSEMBLY 0.333,2.771 0.927,3.135 0.594,0.365 10 E58 5.208,2 6.885,2.844 1.677,0.844 10 COMBINATION METER ASSEMBLY 5.219,1.844 5.792,2.208 0.573,0.365 10 E34 2.677,2.323 5.104,2.833 2.427,0.51 10 DOOR CONTROL RECEIVER*2 2.667,2.156 3.354,2.573 0.688,0.417 10 E62 2.792,1.427 3.271,1.781 0.479,0.354 10 *1 2.698,1.698 3.167,1.99 0.469,0.292 10 *2 1.938,2.208 2.385,2.635 0.448,0.427 10 14 1.938,1.417 2.406,1.792 0.469,0.375 10 12 1.969,0.74 2.385,1.146 0.417,0.406 10 2 1.958,0.25 2.365,0.677 0.406,0.427 10 1 1.74,2.323 2.063,2.594 0.323,0.271 10 E 1.625,1.521 2.125,1.885 0.5,0.365 10 IND 1.688,0.833 2.208,1.188 0.521,0.354 10 IG 1.656,0.354 2.073,0.719 0.417,0.365 10 +B 2.99,1.802 3.427,2.135 0.438,0.333 10 11 4.094,1.802 4.406,2.094 0.313,0.292 10 3 6.396,1.427 6.771,1.75 0.375,0.323 10 16 5.385,1.427 5.885,1.802 0.5,0.375 10 34 6.229,1.521 6.563,1.875 0.333,0.354 10 E 5.635,1.521 6.031,1.896 0.396,0.375 10 B

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the transponder key ECU assembly, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 103
OK:

DTC is not output.


Result:
Proceed to
OK
NG




OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER OR TECHSTREAM (SECURITY INDICATOR)

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER OR TECHSTREAM (SECURITY INDICATOR)
a.

Check that the combination meter assembly (security indicator light) illuminates when operating it with the Active Test.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 103 1
Body Electrical > Immobiliser > Active Test
Tester Display Control Range Inspection Item Diagnostic Note
Security Indicator ON/OFF Security indicator light The test is possible when the following condition is met:

The key is in the ignition key cylinder.


OK:

Combination meter assembly (security indicator light) can be turned on and off using the intelligent tester or Techstream.


Result:
Proceed to
OK
NG




OK

3.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (ENGINE IMMOBILISER SYSTEM STATUS)

NG

5.CHECK VEHICLE CONDITION
3.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (ENGINE IMMOBILISER SYSTEM STATUS)
a.

Turn the ignition switch off.


b.

Using the intelligent tester or Techstream, read the Data List.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Immobiliser > Data List
Tester Display
Immobiliser
50003 103 8
Body Electrical > Immobiliser > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Engine immobiliser system status determined by transponder key ECU assembly Set or Unset Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])
Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.
OK:

On the intelligent tester or Techstream screen, the display changes between Set and Unset as shown in the table above.


Result:
Proceed to
OK
NG




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)
B242622C03
1.469,0.094 2.052,0.438 0.583,0.344 2.188,1.396 2.406,1.792 true 0.875,1.188 0.542,1.771 true 1.042,1.198 0.938,1.792 true 0.177,0.188 0.583,0.5 0.406,0.313 10 *a 0.365,1.792 0.802,2.156 0.438,0.365 10 +B 2.427,1.792 2.781,2.042 0.354,0.25 10 E 0.854,1.823 1.313,2.125 0.458,0.302 10 IG 1.635,0.188 2.25,0.573 0.615,0.385 10 E58
*a Front view of wire harness connector
(to Transponder Key ECU Assembly)


a.

Disconnect the E58 transponder key ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E58-14 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E58-1 (+B) - Body ground Always 11 to 14 V
E58-2 (IG) - Body ground Ignition switch off Below 1 Ω
Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK VEHICLE CONDITION
a.

Check the vehicle condition.

Result:
Result Proceed to
w/o Wireless Door Lock System A
w/ Wireless Door Lock System B




A

6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - COMBINATION METER AND BODY GROUND)

B

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - DOOR CONTROL RECEIVER)
6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - COMBINATION METER AND BODY GROUND)
a.

Disconnect the E58 transponder key ECU assembly connector.


b.

Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E58-12 (IND) - E34-34 (B) Always Below 1 Ω
E34-16 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E58-12 (IND) or E34-34 (B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

7.REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE COMBINATION METER ASSEMBLY
a.

Temporarily replace the combination meter assembly with a new or normally functioning one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

When the immobiliser is set (the ignition switch is off), check that the security indicator light blinks.

OK:

Security indicator light blinks.


Result:
Proceed to
OK
NG




OK

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - DOOR CONTROL RECEIVER)
a.

Disconnect the E58 transponder key ECU assembly connector.


b.

Disconnect the E62 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E58-12 (IND) - E62-11 (IMO) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E58-12 (IND) or E62-11 (IMO) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

9.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - COMBINATION METER AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - COMBINATION METER AND BODY GROUND)
a.

Disconnect the E34 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E62-3 (IND) - E34-34 (B) Always Below 1 Ω
E34-16 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E62-3 (IND) or E34-34 (B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

10.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or normally functioning one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER>REMOVAL


b.

When the immobiliser is set (the ignition switch is off), check that the security indicator light blinks.

OK:

Security indicator light blinks.


Result:
Result Proceed to
NG A
OK B




A

11.REPLACE COMBINATION METER ASSEMBLY

B

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

11.REPLACE COMBINATION METER ASSEMBLY
a.

Temporarily replace the combination meter assembly with a new or normally functioning one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

When the immobiliser is set (the ignition switch is off), check that the security indicator light blinks.

OK:

Security indicator light blinks.


Result:
Proceed to
OK
NG




OK

END (COMBINATION METER ASSEMBLY WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY