Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015208 STEERING PAD N

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

HINT:

When scrapping a vehicle equipped with the SRS or disposing of the steering pad assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the service department of the distributor.


CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a steering pad assembly that has an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft) away from the steering pad assembly.

·

The steering pad assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a steering pad assembly with a deployed airbag.

·

Do not apply water, etc. to a steering pad assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



Hide 45130 2.DISPOSE OF STEERING PAD ASSEMBLY (When Installed in Vehicle)

CAUTION:

Be sure to follow the procedure detailed below when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N01
0.145,0.656 0.521,0.857 0.376,0.201 10 SST 0.964,1.227 0.735,0.775 false 0.735,0.775 0.548,0.775 false

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool).


i.
C110372C05
0.138,0.604 0.456,0.806 0.317,0.201 10 SST 2.746,0.627 2.96,0.828 0.214,0.201 10 *1 0.495,0.719 0.836,0.719 0.836,0.719 0.836,1.649 false 2.733,0.735 2.53,0.735 false
*1 Battery


Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.
C110475N01
0.49,0.17 0.815,0.371 0.325,0.201 10 SST 0.847,0.281 1.766,0.281 1.766,0.281 1.766,0.638 false

Check the function of SST.

Press SST activation switch and check that the LED of SST activation switch comes on.

CAUTION:
·

Do not connect SST connector (yellow colored) to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST may be malfunctioning, so replace SST with a new one.




iii.

Disconnect SST from the battery.




c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



d.

Remove the lower steering column cover (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL).


e.

Install SST.

CAUTION:

Check that there is no looseness in the steering wheel assembly and steering pad assembly.


i.
B266979C01
2.583,3.073 2.75,3.073 2.75,3.073 2.75,2.927 false 1.094,3.073 0.927,3.073 0.927,3.073 0.927,2.885 true 1.115,2.958 1.313,3.135 0.198,0.177 10 *1 2.406,2.99 2.594,3.146 0.188,0.156 10 *2
*1 Lock Slider
*2 Airbag Connector (Yellow Colored)


Pull the lock slider in the direction indicated by the arrow to release the connector lock and disconnect the airbag connector (yellow colored) from the spiral cable with sensor.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



ii.
B296831C01
1.083,1.104 0.927,1.104 0.927,1.104 0.75,0.927 true 0.688,2.896 1.802,2.896 1.802,2.896 1.948,2.677 true 1.146,2.896 1.354,2.604 true 1.135,1.031 1.573,1.188 0.438,0.156 10 *1 (*a) 0.344,2.813 0.781,2.969 0.438,0.156 10 SST
*1 Lock Slider
*a Lock Position


Connect SST connector to the airbag connector of the spiral cable.

SST
09082-00700  
09082-00780  

NOTICE:

To avoid damaging SST connector and the wire harness, do not lock the secondary lock of the twin lock.



iii.

Check that the lock slider is in the lock position.



f.

Close all doors.


g.
B328813C01
2.719,1.5 2.833,1.167 2.833,1.167 3,1.167 false 1.698,0.823 1.583,0.5 1.583,0.5 1.417,0.5 false 3.052,1.094 3.365,1.271 0.313,0.177 10 SST 1.188,0.417 1.5,0.615 0.313,0.198 10 *1 1.635,1.708 1.948,1.906 0.313,0.198 10 *a
*1 Battery
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the vehicle front side window.

Text in Illustration
*1
*a


h.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


iii.

Press SST activation switch to deploy the airbag.

CAUTION:
·

When deploying the airbag, make sure that no one is near the vehicle.

·

The steering pad assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a steering pad assembly with a deployed airbag.

·

Do not apply water, etc. to a steering pad assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




Hide 45130 3.DISPOSE OF STEERING PAD ASSEMBLY (When Not Installed in Vehicle)

NOTICE:

Be sure to observe the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N01
0.145,0.656 0.521,0.857 0.376,0.201 10 SST 0.964,1.227 0.735,0.775 false 0.735,0.775 0.548,0.775 false

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST:

SRS Airbag Deployment Tool


i.
C110372C05
0.138,0.604 0.456,0.806 0.317,0.201 10 SST 2.746,0.627 2.96,0.828 0.214,0.201 10 *1 0.495,0.719 0.836,0.719 0.836,0.719 0.836,1.649 false 2.733,0.735 2.53,0.735 false
*1 Battery


Connect SST to the battery.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.
C110475N01
0.49,0.17 0.815,0.371 0.325,0.201 10 SST 0.847,0.281 1.766,0.281 1.766,0.281 1.766,0.638 false

Check the function of SST.

Press the SST activation switch and check that the LED of the SST activation switch comes on.

CAUTION:
·

Do not connect the yellow SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST is malfunctioning. Replace SST.




iii.

Disconnect SST from the battery.



b.

Remove the horn button assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL).

CAUTION:
·

Before removing the horn button assembly, wait at least 90 seconds after turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal.

·

When storing the horn button assembly, keep the airbag deployment side facing upward.




c.
B104882C12
2.24,0.938 2.74,0.438 2.74,0.438 2.51,0.438 false 2.677,1.5 2.875,1.698 0.198,0.198 10 *a 2.281,0.375 2.5,0.573 0.219,0.198 10 *1
*1 Stripped Wire Section
*a Wire Diameter


Using braided wire, tie down the horn button assembly to an unneeded wheel.

Wire:

Stripped wire section

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the horn button assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire section:

Area = 3.14 x (Diameter)2 / 4


i.
B288998N01
1.802,1.979 1.802,1.396 1.802,1.396 2.583,1.396 false 2.25,1.854 2.25,1.396 false 2.615,1.354 2.906,1.51 0.292,0.156 10 SST

After connecting the following SST to each other, connect them to the horn button assembly.

SST
09082-00802  (09082-10801, 09082-40800)


ii.
B288999C01
2.281,1.354 2.094,1.552 2.094,1.552 1.938,1.552 true 1.25,1.469 1.25,1.917 true 1.125,2.688 1.125,2.25 1.125,2.25 2.729,2.25 true 2.385,2.677 2.385,2.25 true 1.823,3.625 2.438,3.625 true 1.188,1.906 1.385,2.094 0.198,0.188 10 *a 1.75,1.469 1.906,1.667 0.156,0.198 10 *a 2.479,3.552 2.677,3.75 0.198,0.198 10 *a 2.781,2.167 2.938,2.365 0.156,0.198 10 *a
*a 2 times or more


Wind 3 wires at least 2 times each around each of the snap pins.

CAUTION:
·

Tightly wind the wires around the snap pins without any slack.

·

Make sure that the wires are tight. If there is slack in the wires, the horn button assembly may break loose when the airbag is deployed.




iii.
B279731

Face the airbag deployment side of the horn button assembly upward on top of an unneeded tire and wheel set. Separately tie the each sides of the horn button assembly to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the horn button assembly may break loose when the airbag is deployed.

·

Always tie down the horn button assembly with the airbag deployment side facing upward.



NOTICE:

The wheel will be damaged by the airbag deployment, so use an unneeded wheel.




d.
B279732N02
2.194,0.271 2.505,0.437 0.312,0.166 10 SST 3.145,0.725 2.785,0.365 2.785,0.365 2.577,0.365 false

Install SST.

CAUTION:

Place the wheel on level ground.


i.

Connect the SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the disc wheel.



ii.
C271015C01
0.958,1.458 1.156,1.458 false 1.198,1.375 1.656,1.573 0.458,0.198 10 SST 1.365,1.75 1.677,1.948 0.313,0.198 10 *a
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the wheel.



e.

Cover the horn button assembly (using a cardboard box).

i.
C188669C02
2.469,1.552 2.802,1.552 true 0.99,1.406 0.635,1.406 true 1.146,0.031 1.26,0.177 0.115,0.146 10 Y 1.063,0.729 1.177,0.875 0.115,0.146 10 Y 2.781,0.844 2.906,0.99 0.125,0.146 10 X 0.417,1.333 0.604,1.51 0.188,0.177 10 *1 2.854,1.469 3.042,1.646 0.188,0.177 10 *1
*1 Weight


Cover the horn button assembly with a cardboard box.


ii.

Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).

Minimum cardboard box size:

Must exceed the following dimensions

X:

460 mm (1.51 ft.)

Y:

650 mm (2.13 ft.)


NOTICE:
·

When dimension Y of the cardboard box exceeds the diameter of the wheel and tire to which the horn button assembly is tied, X should be the following size.

X = 460 mm (1.51 ft.) + width of tire

·

If a cardboard box smaller than the specified size is used, it may be broken by the shock from the airbag deployment.





f.

Cover the horn button assembly (using tires).

i.
C188667C02
1.617,0.378 1.8,0.534 0.183,0.156 10 *a 2.621,0.928 2.812,1.08 0.19,0.153 10 *b 0.594,1.761 0.819,1.927 0.225,0.167 10 *1
*1 Tires (3 or more)
*a Inner Diameter
*b Width


Place at least 3 tires without wheels onto the wheel and tire to which the horn button assembly is tied.


ii.

Place a wheel and tire on top.

Minimum tire size:
Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:

Do not use tires with wheels except for on the top and bottom.


NOTICE:
·

The tires may be damaged by the airbag deployment, so use unneeded tires.

·

Do not place the SST connector under the tire because it could be damaged.




iii.
C223306

Tie the tires together with the 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.




g.

Deploy the airbag.

i.
C188670C02
2.552,1.521 2.917,1.896 2.917,1.896 2.917,2.083 true 2.667,3.5 2.99,3.823 2.99,3.823 2.99,4.021 true 1.396,3.365 1.698,3.365 false 0.729,1.219 0.573,1.219 false 0.396,3.24 0.729,3.24 false 1.396,1.354 1.667,1.354 false 1.385,2.042 1.594,2.198 0.208,0.156 10 *a 0.208,2.323 0.49,2.49 0.281,0.167 10 *B 0.208,0.073 0.49,0.24 0.281,0.167 10 *A 2.854,2.094 3.052,2.26 0.198,0.167 10 *2 1.688,1.271 1.917,1.448 0.229,0.177 10 *1 0.24,1.135 0.542,1.281 0.302,0.146 10 SST 0.073,3.167 0.375,3.313 0.302,0.146 10 SST 1.729,3.271 1.938,3.469 0.208,0.198 10 *1 2.927,4.063 3.125,4.229 0.198,0.167 10 *2 1.375,4.083 1.583,4.24 0.208,0.156 10 *a
*A Using a Cardboard Box
*B Using Tires
*1 Battery
*2 Horn Button Assembly
*a 10 m (32.8 ft.) or more


Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the horn button assembly is tied.


iii.

Press the SST activation switch to deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.




h.

Dispose of the horn button assembly.

CAUTION:
·

The horn button assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a horn button assembly with a deployed airbag.

·

Do not apply water etc. to a horn button assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the horn button assembly from the wheel.


ii.

Place the horn button assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.