Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.11–2013.04
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1600/15  Front Airbag Sensor Assembly RH  


DESCRIPTION

The front airbag sensor RH circuit consists of the center airbag sensor assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.

DTC B1600/15 is stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1600/15 Front Airbag Sensor Assembly RH One of the following conditions is met:
·

The center airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit.

·

A front airbag sensor RH malfunction.

·

A center airbag sensor assembly malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Center airbag sensor assembly


DTC is not output in check mode

WIRING DIAGRAM

C238208E06
1.198,1.01 1.646,1.177 0.448,0.167 10 SRH+ 5.615,1.042 5.979,1.208 0.365,0.167 10 SR+ 5.615,2.208 5.979,2.375 0.365,0.167 10 SR- 1.198,2.156 1.646,2.323 0.448,0.167 10 SRH- 1.74,0.917 1.885,1.063 0.146,0.146 10 2 5.302,0.917 5.51,1.063 0.208,0.146 10 12 5.302,2.083 5.51,2.229 0.208,0.146 10 13 1.74,2.073 1.885,2.219 0.146,0.146 10 1 3.427,0.813 3.573,0.958 0.146,0.146 10 2 3.427,1.979 3.573,2.125 0.146,0.146 10 1 3.333,1.031 3.635,1.219 0.302,0.188 10 AE5 3.333,2.198 3.635,2.385 0.302,0.188 10 AE5 0.042,3.844 0.323,4.021 0.281,0.177 10 A11 5.333,3.844 5.615,4.021 0.281,0.177 10 E60 0.042,4.01 2,4.354 1.958,0.344 10 FRONT AIRBAG SENSOR RH 5.333,4.01 7.167,4.354 1.833,0.344 10 CENTER AIRBAG SENSOR ASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor assembly and front airbag sensor RH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor assembly and front airbag sensor RH.


b.
C251569C01
0.241,1.477 0.431,1.621 0.191,0.143 10 *1 2.288,1.485 2.444,1.663 0.156,0.178 10 *2
*1 Front Airbag Sensor RH
*2 Center Airbag Sensor Assembly


Check that the connectors (on the center airbag sensor assembly side and front airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Result:
Proceed to
OK
NG




OK

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C251570C01
5.188,0.573 5.583,0.813 0.396,0.24 3.115,0.573 3.51,0.813 0.396,0.24 3.938,0.906 3.594,1.365 true 4.083,0.906 4.438,1.375 true 6.042,0.844 5.698,1.25 true 6.135,0.844 6.531,1.26 true 6.073,1.313 6.01,1.542 false 5.26,0.615 5.563,0.802 0.302,0.188 10 E60 0.385,1.094 0.583,1.333 0.198,0.24 10 *1 3.281,0.083 3.469,0.24 0.188,0.156 10 *a 3.188,0.615 3.5,0.792 0.313,0.177 10 A11 5.323,0.083 5.51,0.24 0.188,0.156 10 *b 1.708,1.042 1.917,1.25 0.208,0.208 10 *2 3.927,0.344 4.115,0.5 0.188,0.156 10 *3 6,0.125 6.188,0.281 0.188,0.156 10 *4 5.927,1.573 6.167,1.75 0.24,0.177 10 *5 0.688,0.729 0.833,0.917 0.146,0.188 10 F 1.792,0.729 1.906,0.885 0.115,0.156 10 A 1.521,0.927 1.667,1.167 0.146,0.24 10 B 1.281,0.917 1.417,1.167 0.135,0.25 10 C 1.167,0.917 1.333,1.167 0.167,0.25 10 D 0.927,0.906 1.167,1.083 0.24,0.177 10 E 3.219,1.396 3.865,1.625 0.646,0.229 10 1 (SRH-) 4.24,1.396 4.885,1.625 0.646,0.229 10 2 (SRH+) 5.208,1.281 5.833,1.5 0.625,0.219 10 12 (SR+) 6.385,1.281 7,1.5 0.615,0.219 10 13 (SR-)
*1 Front Airbag Sensor RH *2 Center Airbag Sensor Assembly
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
*b Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A11-2 (SRH+) - Body ground Ignition switch ON Below 1 V
A11-1 (SRH-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 12 (SR+) and 13 (SR-) of connector B.NOTICE:

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A11-2 (SRH+) - A11-1 (SRH-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A11-2 (SRH+) - A11-1 (SRH-) Always 1 MΩ or higher
A11-2 (SRH+) - Body ground Always 1 MΩ or higher
A11-1 (SRH-) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK FRONT AIRBAG SENSOR RH

NG

6.CHECK INSTRUMENT PANEL WIRE
4.CHECK FRONT AIRBAG SENSOR RH
a.

Inspect the front airbag sensor RH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

5.CHECK DTC

NG

5.CHECK DTC
a.

Connect the connectors to the center airbag sensor assembly and front airbag sensor RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1600/15 is not output.


Result:
Proceed to
OK
NG




OK

NG

6.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C251572C01
5.292,0.458 5.688,0.698 0.396,0.24 3.25,0.458 3.646,0.698 0.396,0.24 1.5,0.76 1.5,0.333 1.5,0.333 1.385,0.333 false 4.156,0.74 4.313,1.146 true 4.042,0.74 3.875,1.146 true 6.24,0.813 6.635,1.188 true 6.135,0.813 5.729,1.188 true 6.167,1.271 6.094,1.479 false 1.094,0.875 1.094,1.208 false 0.344,1.115 0.615,1.323 0.271,0.208 10 *1 1.75,1.073 2.021,1.281 0.271,0.208 10 *2 1.031,1.229 1.302,1.438 0.271,0.208 10 *3 1.208,0.25 1.479,0.458 0.271,0.208 10 *4 4,0.24 4.271,0.448 0.271,0.208 10 *5 6.104,0.083 6.375,0.292 0.271,0.208 10 *6 1.844,0.74 2,0.927 0.156,0.188 10 A 1.177,0.938 1.333,1.125 0.156,0.188 10 D 1.323,0.938 1.479,1.125 0.156,0.188 10 C 0.917,0.938 1.073,1.125 0.156,0.188 10 E 1.583,0.938 1.74,1.125 0.156,0.188 10 B 5.375,0.51 5.667,0.667 0.292,0.156 10 E60 3.313,0.51 3.604,0.667 0.292,0.156 10 AE5 6.01,1.51 6.229,1.688 0.219,0.177 10 *7 4.313,1.167 4.542,1.375 0.229,0.208 10 1 3.833,1.167 4.063,1.375 0.229,0.208 10 2 6.51,1.229 7.146,1.438 0.635,0.208 10 13 (SR-) 5.281,1.229 5.917,1.438 0.635,0.208 10 12 (SR+) 5.542,0.042 5.813,0.25 0.271,0.208 10 *b 3.583,0.042 3.854,0.25 0.271,0.208 10 *a
*1 Front Airbag Sensor RH *2 Center Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AE5-1 (SR-) - Body ground Ignition switch ON Below 1 V
AE5-2 (SR+) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 12 (SR+) and 13 (SR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AE5-1 (SR-) - AE5-2 (SR+) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AE5-1 (SR-) - AE5-2 (SR+) Always 1 MΩ or higher
AE5-1 (SR-) - Body ground Always 1 MΩ or higher
AE5-2 (SR+) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE