Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.11–2013.04
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1605/15  Front Airbag Sensor Assembly LH  


DESCRIPTION

The front airbag sensor LH circuit consists of the center airbag sensor assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbag should be deployed.

DTC B1605/15 is stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1605/15 Front Airbag Sensor Assembly LH One of the following conditions is met:
·

The center airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit.

·

A front airbag sensor LH malfunction.

·

A center airbag sensor assembly malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Center airbag sensor assembly


DTC is not output in check Mode.

WIRING DIAGRAM

C238209E07
1.229,1.031 1.625,1.229 0.396,0.198 10 SLH+ 5.625,1.031 5.958,1.229 0.333,0.198 10 SL+ 5.625,2.188 5.958,2.385 0.333,0.198 10 SL- 1.26,2.198 1.656,2.396 0.396,0.198 10 SLH- 1.75,0.927 1.948,1.094 0.198,0.167 10 2 5.302,0.927 5.5,1.094 0.198,0.167 10 14 5.302,2.094 5.5,2.26 0.198,0.167 10 20 1.74,2.104 1.938,2.271 0.198,0.167 10 1 3.427,0.854 3.625,1.021 0.198,0.167 10 1 3.427,2.021 3.625,2.188 0.198,0.167 10 2 3.333,1.031 3.615,1.188 0.281,0.156 10 BE7 3.333,2.208 3.615,2.365 0.281,0.156 10 BE7 5.302,3.833 5.583,3.99 0.281,0.156 10 E60 0.177,3.833 0.458,3.99 0.281,0.156 10 B14 0.177,3.99 2.146,4.323 1.969,0.333 10 FRONT AIRBAG SENSOR LH 5.302,3.99 7.094,4.521 1.792,0.531 10 CENTER AIRBAG SENSOR ASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor assembly and front airbag sensor LH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor assembly and front airbag sensor LH.


b.
C251569C01
0.241,1.477 0.431,1.621 0.191,0.143 10 *1 2.288,1.485 2.444,1.663 0.156,0.178 10 *2
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor Assembly


Check that the connectors (on the center airbag sensor assembly side and front airbag sensor LH side) are not damaged.

Result:
Proceed to
OK
NG




OK

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C251573C01
5.292,0.583 5.688,0.823 0.396,0.24 3.125,0.583 3.521,0.823 0.396,0.24 4.094,0.896 4.385,1.375 true 3.938,0.896 3.656,1.375 true 6.208,0.844 6.552,1.198 true 6.042,0.958 5.75,1.271 true 6.115,1.271 6.021,1.469 false 5.427,0.042 5.615,0.198 0.188,0.156 10 *b 6.021,0.115 6.208,0.271 0.188,0.156 10 *4 3.385,0.042 3.573,0.198 0.188,0.156 10 *a 3.198,0.635 3.49,0.792 0.292,0.156 10 B14 5.344,0.635 5.635,0.792 0.292,0.156 10 E60 0.313,1.156 0.5,1.333 0.188,0.177 10 *1 1.656,1.104 1.917,1.333 0.26,0.229 10 *2 3.948,0.292 4.135,0.448 0.188,0.156 10 *3 1.76,0.792 1.875,0.958 0.115,0.167 10 A 1.469,0.99 1.604,1.167 0.135,0.177 10 B 1.229,0.99 1.354,1.188 0.125,0.198 10 C 1.115,0.99 1.25,1.146 0.135,0.156 10 D 0.875,0.99 0.99,1.156 0.115,0.167 10 E 0.604,0.771 0.719,0.938 0.115,0.167 10 F 3.146,1.396 3.75,1.604 0.604,0.208 10 1 (SLH-) 5.906,1.49 6.094,1.646 0.188,0.156 10 *5 4.354,1.396 5.083,1.604 0.729,0.208 10 2 (SLH+) 5.573,1.271 5.917,1.417 0.344,0.146 10 SL- 6.563,1.208 6.906,1.354 0.344,0.146 10 SL+
*1 Front Airbag Sensor LH *2 Center Airbag Sensor Assembly
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B14-2 (SLH+) - Body ground Ignition switch ON Below 1 V
B14-1 (SLH-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 14 (SL+) and 20 (SL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B14-2 (SLH+) - B14-1 (SLH-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B14-2 (SLH+) - B14-1 (SLH+) Always 1 MΩ or higher
B14-2 (SLH+) - Body ground Always 1 MΩ or higher
B14-1 (SLH-) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK FRONT AIRBAG SENSOR LH

NG

6.CHECK INSTRUMENT PANEL WIRE
4.CHECK FRONT AIRBAG SENSOR LH
a.

Inspect the front airbag sensor LH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>ON-VEHICLE INSPECTION

Result:
Proceed to
OK
NG




OK

5.CHECK DTC

NG

5.CHECK DTC
a.

Connect the connectors to the center airbag sensor assembly and front airbag sensor LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTC B1605/15 is not output.


Result:
Proceed to
OK
NG




OK

NG

6.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C251574C01
5.292,0.438 5.688,0.677 0.396,0.24 3.302,0.438 3.698,0.677 0.396,0.24 4.156,0.75 4.333,1.135 true 4.042,0.75 3.865,1.135 true 6.302,0.813 6.656,1.26 true 6.146,0.927 5.833,1.198 true 6.208,1.271 6.073,1.479 false 1.5,0.74 1.5,0.354 1.5,0.354 1.396,0.354 false 1.094,0.844 1.094,1.177 false 0.354,1.094 0.604,1.302 0.25,0.208 10 *1 1.75,1.021 2,1.229 0.25,0.208 10 *2 4.021,0.271 4.271,0.479 0.25,0.208 10 *5 6.125,0.063 6.375,0.271 0.25,0.208 10 *6 0.667,0.729 0.823,0.906 0.156,0.177 10 F 1.177,0.906 1.333,1.083 0.156,0.177 10 D 1.313,0.906 1.469,1.083 0.156,0.177 10 C 0.927,0.906 1.083,1.083 0.156,0.177 10 E 1.594,0.906 1.75,1.083 0.156,0.177 10 B 1.854,0.729 2.01,0.906 0.156,0.177 10 A 5.51,0.063 5.76,0.271 0.25,0.208 10 *b 3.5,0.063 3.75,0.271 0.25,0.208 10 *a 5.365,0.479 5.656,0.635 0.292,0.156 10 E60 3.365,0.479 3.656,0.635 0.292,0.156 10 BE7 4.354,1.156 4.552,1.365 0.198,0.208 10 1 3.802,1.167 4,1.375 0.198,0.208 10 2 6.583,1.281 7.135,1.521 0.552,0.24 10 20 (SL-) 5.323,1.219 5.917,1.417 0.594,0.198 10 14 (SL+) 5.948,1.51 6.167,1.667 0.219,0.156 10 *7 1.031,1.198 1.281,1.406 0.25,0.208 10 *3 1.229,0.281 1.479,0.49 0.25,0.208 10 *4
*1 Front Airbag Sensor LH *2 Center Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Center Airbag Sensor Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
BE7-1 (SL+) - Body ground Ignition switch ON Below 1 V
BE7-2 (SL-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 14 (SL+) and 20 (SL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
BE7-1 (SL+) - BE7-2 (SL-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
BE7-1 (SL+) - BE7-2 (SL-) Always 1 MΩ or higher
BE7-1 (SL+) - Body ground Always 1 MΩ or higher
BE7-2 (-SL-) - Body ground Always 1 MΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE