Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.11–2013.04
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/53  Short in Front Passenger Side Squib Circuit  B1806/54  Open in Front Passenger Side Squib Circuit  B1807/51  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the center airbag sensor assembly and the instrument panel passenger airbag assembly.

The circuit signals the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front passenger side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1805/53 Short in Front Passenger Side Squib Circuit One of the following conditions is met:
·

Short in front passenger side squib circuit.

·

Front passenger side squib malfunction.

·

Center airbag sensor assembly malfunction.


·

Instrument panel wire

·

Instrument panel passenger airbag assembly (front passenger side squib)

·

Center airbag sensor assembly


DTC is output in check mode
B1806/54 Open in Front Passenger Side Squib Circuit One of the following conditions is met:
·

Open in front passenger side squib circuit.

·

Front passenger side squib malfunction.

·

Center airbag sensor assembly malfunction.


·

Instrument panel wire

·

Instrument panel passenger airbag assembly (front passenger side squib)

·

Center airbag sensor assembly


DTC is output in check mode
B1807/51 Short to GND in Front Passenger Side Squib Circuit One of the following conditions is met:
·

Short to ground in front passenger side squib circuit.

·

Front passenger side squib malfunction.

·

Center airbag sensor assembly malfunction.


·

Instrument panel wire

·

Instrument panel passenger airbag assembly (front passenger side squib)

·

Center airbag sensor assembly


DTC is output in check mode
B1808/52 Short to B+ in Front Passenger Side Squib Circuit One of the following conditions is met:
·

Short to B+ in front passenger side squib circuit.

·

Front passenger side squib malfunction.

·

Center airbag sensor assembly malfunction.


·

Instrument panel wire

·

Instrument panel passenger airbag assembly (front passenger side squib)

·

Center airbag sensor assembly


DTC is output in check mode

WIRING DIAGRAM

C251577E02
5.031,2.948 6.844,3.344 1.813,0.396 10 CENTER AIRBAG SENSOR ASSEMBLY 0.729,2.948 3.635,3.521 2.906,0.573 10 INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (Front Passenger Side Squib) 5.031,2.75 5.438,2.938 0.406,0.188 10 E60 0.729,2.75 1.135,2.938 0.406,0.188 10 E61 5.156,0.875 5.313,1.063 0.156,0.188 10 1 5.156,1.896 5.313,2.083 0.156,0.188 10 2 2.125,0.875 2.438,1.063 0.313,0.188 10 1 2.135,1.885 2.448,2.073 0.313,0.188 10 2 1.865,1.885 2.177,2.073 0.313,0.188 10 P- 1.833,0.885 2.146,1.073 0.313,0.188 10 P+ 5.385,2 5.792,2.188 0.406,0.188 10 AP- 5.385,0.969 5.792,1.156 0.406,0.188 10 AP+

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester or Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
SST
09843-18061  

a.
C251578C01
0.573,2.625 1,2.917 0.427,0.292 0.938,1.281 0.938,1.74 false 2.125,3.323 2.365,3.323 false 0.667,2.698 0.958,2.854 0.292,0.156 10 E61 0.875,1.76 1.104,1.938 0.229,0.177 10 *1 1.063,1.385 1.24,1.563 0.177,0.177 10 D 1.333,1.385 1.51,1.563 0.177,0.177 10 C 1.552,2.365 1.781,2.542 0.229,0.177 10 *3 1.906,1.156 2.135,1.333 0.229,0.177 10 A 1.729,1.583 1.958,1.76 0.229,0.177 10 *2 2.448,3.229 2.781,3.406 0.333,0.177 10 SST
*1 Instrument Panel Passenger Airbag Assembly
(Front Passenger Side Squib)
*2 Instrument Panel Wire
*3 Center Airbag Sensor Assembly
*4 Connector C
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib))


Disconnect the connector from the instrument panel passenger airbag assembly.


b.

Connect the black wire side of SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert the SST into the terminals of the connector when connecting.

·

Insert the SST straight into the terminals of the connector.




c.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check the DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTCs B1805/53, B1806/54, B1807/51 and B1808/52 are not output.


HINT:

DTCs other than DTCs B1805/53, B1806/54, B1807/51 and B1808/52 may be output at this time, but they are not related to this check.


Result:
Prooceed to
OK
NG




OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the SST from connector C.


d.
C251579C01
1.344,0.969 1.344,0.573 1.344,0.573 1.208,0.573 false 0.667,1.146 0.667,1.49 false 0.583,1.521 0.781,1.719 0.198,0.198 10 *1 1.802,1.49 2,1.688 0.198,0.198 10 *2 1,0.5 1.198,0.698 0.198,0.198 10 *3 1.583,1.25 1.781,1.448 0.198,0.198 10 B 1.01,1.25 1.208,1.448 0.198,0.198 10 C 0.781,1.25 0.979,1.448 0.198,0.198 10 D 1.969,0.99 2.167,1.188 0.198,0.198 10 A
*1 Instrument Panel Passenger Airbag Assembly
(Front Passenger Side Squib)
*2 Center Airbag Sensor Assembly
*3 Instrument Panel Wire


Disconnect the connectors from the center airbag sensor assembly.


e.

Check that the connectors (on the center airbag sensor assembly side and instrument panel passenger airbag side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Result:
Proceed to
OK
NG




OK

3.CHECK INSTRUMENT PANEL WIRE

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK INSTRUMENT PANEL WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.
C251585C01
1.104,2.375 1.49,2.604 0.385,0.229 0.917,1.229 0.917,1.5 false 1.385,0.635 1.51,0.635 1.51,0.635 1.51,1.073 false 2.135,2.781 2.323,3.104 true 1.906,2.771 1.719,3.094 true 1.042,1.302 1.198,1.479 0.156,0.177 10 D 1.281,1.313 1.438,1.49 0.156,0.177 10 C 1.635,1.302 1.792,1.479 0.156,0.177 10 B 1.99,1.063 2.146,1.24 0.156,0.177 10 A 0.844,1.521 1.083,1.729 0.24,0.208 10 *1 2.177,1.479 2.406,1.688 0.229,0.208 10 *2 1.198,0.563 1.406,0.75 0.208,0.188 10 *3 1.156,2.406 1.458,2.573 0.302,0.167 10 E61 1.917,1.958 2.125,2.146 0.208,0.188 10 *4 1.26,1.885 1.458,2.073 0.198,0.188 10 *a 2.354,3.125 2.646,3.313 0.292,0.188 10 P- 1.583,3.125 1.875,3.313 0.292,0.188 10 P+
*1 Instrument Panel Passenger Airbag Assembly
(Front Passenger Side Squib)
*2 Center Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Connector C
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib))


Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester connection Condition Specified condition
E61-1 (P+) - Body ground Ignition switch ON Below 1 V
E61-2 (P-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester connection Condition Specified condition
E61-1 (P+) - E61-2 (P-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester connection Condition Specified condition
E61-1 (P+) - E61-2 (P-) Always 1 MΩ or higher
E61-1 (P+) - Body ground Always 1 MΩ or higher
E61-2 (P-) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to the original condition.

Result:
Proceed to
OK
NG




OK

4.CHECK DTC

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK DTC
a.
C251586C01
0.979,1.083 0.979,1.375 false 0.906,1.417 1.115,1.615 0.208,0.198 10 *1 1.688,1.365 1.896,1.563 0.208,0.198 10 *2
*1 Instrument Panel Passenger Airbag Assembly
(Front Passenger Side Squib)
*2 Center Airbag Sensor Assembly


Connect the connectors to the instrument panel passenger airbag assembly and the center airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Body Electrical > SRS Airbag > Clear DTCs
50002 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check the DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 102

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

OK:

DTCs B1805/53, B1806/54, B1807/51 and B1808/52 are not output.


HINT:

DTCs other than DTCs B1805/53, B1806/54, B1807/51 and B1808/52 may be output at this time, but they are not related to this check.


Result:
Proceed to
OK
NG




OK

NG