Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM19Y0E _58 Vehicle Interior _003012 SEAT BELT _0015219 FRONT SEAT OUTER BELT ASSEMBLY N

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a front seat outer belt assembly (with a seat belt pretensioner), always deploy the procedures described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the service dept. of the distributor.


PROCEDURE

Hide 73210 1.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Installed in Vehicle)

CAUTION:
·

Use gloves and safety glasses when handling a front seat outer belt assembly with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.

·

When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.



NOTICE:
·

When disposing of a front seat outer belt assembly with a pretensioner, never deploy the pretensioner in the customer's vehicle.

·

Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.

·

The front seat outer belt assembly produces an exploding sound when the pretensioner deploys, so perform the operation outdoors where it will not disturb local residents.

·

When deploying a seat belt pretensioner, perform the operation at least 10 m (32.8 ft.) away from the front seat outer belt assembly.

·

Be sure to follow the procedure listed below when deploying a seat belt pretensioner.



a.
B050515E18
0.667,0.646 0.979,1.177 true 0.365,0.552 1.052,0.906 0.688,0.354 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.


i.
B050511C02
0.865,1.135 1.177,1.5 true 2.552,0.833 2.271,0.833 true 0.583,1.042 1.198,1.438 0.615,0.396 10 SST 2.583,0.771 2.958,1.156 0.375,0.385 10 *1
*1 Battery


Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
B050514E14
1.302,0.24 1.49,0.531 true 1,0.135 1.594,0.552 0.594,0.417 10 SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.




b.

Disconnect the seat belt pretensioner connector.

i.

Disconnect the cable from the negative (-) battery terminal.


ii.

Remove the front door scuff plate. (Click here Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL)


iii.

Remove the rear door scuff plate. (Click here Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL)


iv.

Remove the center pillar lower garnish. (Click here Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL)


v.
B329911C01
0.896,1.167 1.188,1.365 true 1.208,1.302 1.625,1.688 0.417,0.385 10 *1
*1 Locking Button


Pull the locking button to release the connector lock.


vi.

Disconnect the pretensioner connector from the retractor.

NOTICE:

When handling the pretensioner connector, take care not to damage the pretensioner wire harness.




c.
B221509E02
1.979,1.76 1.792,1.76 true 1.01,1.479 1.01,1.313 true 2,1.677 2.531,1.979 0.531,0.302 10 SST 0.875,1.49 1.375,1.854 0.5,0.365 10 SST

Connect SST.

i.

Connect 2 SST, and then connect them to the seat belt pretensioner.

SST
09082-00700  
09082-00770  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.



ii.
B328836C01
0.469,1.021 0.708,1.406 true 1.656,1.771 2.01,2.104 0.354,0.333 10 *a 0.167,0.906 0.75,1.302 0.583,0.396 10 SST
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the front of the vehicle.


iii.

Close all the doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.




d.

Deploy the seat belt pretensioner.

i.

Confirm that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.


iii.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




e.
B221506

Dispose of the front seat outer belt assembly.

i.

Remove the front seat outer belt assembly and SST.


ii.

Place the front seat outer belt assembly in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:
·

The front seat outer belt assembly becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a front seat outer belt assembly with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.



HINT:

When scrapping a vehicle, deploy the seat belt pretensioner, and then scrap the vehicle with the front seat outer belt assembly installed.




Hide 73210 2.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (When Not Installed in Vehicle)

CAUTION:
·

Use gloves and safety glasses when handling a front seat outer belt assembly with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.

·

When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.



NOTICE:
·

When disposing of a front seat outer belt assembly with a pretensioner, never deploy the pretensioner in the customer's vehicle.

·

Never dispose of a front seat outer belt assembly with a pretensioner that has not been deployed.

·

The front seat outer belt assembly produces an exploding sound when the pretensioner deploys, so perform the operation outdoors where it will not disturb local residents.

·

When deploying a seat belt pretensioner, perform the operation at least 10 m (32.8 ft.) away from the front seat outer belt assembly.

·

Be sure to follow the procedure listed below when deploying a seat belt pretensioner.



a.

Remove the front seat outer belt assembly. (Click here Vehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL)


b.
B121580C03
1.594,0.313 1.917,0.656 0.323,0.344 10 *a 2.365,0.531 2.76,0.896 0.396,0.365 10 *b
*a Cut
*b 100 mm


Wind the front seat outer belt assembly webbing with the retractor.


c.

When the front seat outer belt assembly webbing is sufficiently wound, cut the front seat outer belt assembly webbing approximately 100 mm (3.94 in.) from the retractor, as shown in the illustration.

HINT:

The retractor resistance increases in correlation with how much the front seat outer belt assembly webbing is wound.



d.
B050515E19
1,0.792 1.177,1.177 true 0.698,0.667 1.281,1.083 0.583,0.417 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying a seat belt pretensioner, always use the specified SST.


i.
B050511C03
0.865,1.135 1.177,1.5 true 2.552,0.833 2.271,0.833 true 0.583,1.042 1.167,1.438 0.583,0.396 10 SST 2.583,0.729 2.99,1.135 0.406,0.406 10 *1
*1 Battery


Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
B050514E15
1.302,0.24 1.49,0.531 true 0.99,0.167 1.635,0.49 0.646,0.323 10 SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.




e.
B221509E03
1.979,1.76 1.792,1.76 true 1.01,1.479 1.01,1.313 true 2,1.698 2.698,2.052 0.698,0.354 10 SST 0.885,1.49 1.396,1.792 0.51,0.302 10 SST

Connect SST.

i.

Connect 2 SST, and then connect them to the seat belt pretensioner.

SST
09082-00700  
09082-00770  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.



ii.
B221510E02
2.365,1.052 2.573,0.948 true 2.063,1.521 1.865,1.521 true 2.063,1 2.531,1.302 0.469,0.302 10 SST 2.083,1.427 2.563,1.729 0.479,0.302 10 SST

Place the front seat outer belt assembly on the ground and cover it with a tire and wheel assembly.

NOTICE:
·

Position the front seat outer belt assembly as shown in the illustration.

·

As the disc wheel may be damaged by the airbag deployment, use a disc wheel that you are planning to throw away.

·

As the tires may be damaged by the airbag deployment, use tires that you are planning to throw away.




iii.

Position and hold SST at least 10 m (32.8 ft.) away from the wheel.

NOTICE:

Do not damage the SST wire harness.




f.
B328837C01
0.615,1.281 1.01,1.281 true 1.688,1.75 2.063,2.094 0.375,0.344 10 *a 1.052,1.208 1.531,1.5 0.479,0.292 10 SST
*a 10 m or more


Deploy the seat belt pretensioner.

i.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel.


ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.


iii.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




g.
B221506

Dispose of the front seat outer belt assembly.

i.

Remove the wheel and SST.


ii.

Place the front seat outer belt assembly in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:
·

The front seat outer belt assembly becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a front seat outer belt assembly with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.

·

Do not apply water, etc. to a front seat outer belt assembly with a deployed pretensioner.