Home › Vehicle Interior › SEAT BELT › REAR NO. 1 SEAT OUTER BELT ASSEMBLY
RM19Y0E _58 Vehicle Interior _003012 SEAT BELT _0015221 REAR NO. 1 SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR NO. 1 SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 73360C 1.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY

a.

Engage the 2 guides and install the rear No. 1 seat outer belt assembly with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)


Hide 64730B 2.INSTALL DECK TRIM SIDE PANEL ASSEMBLY (for Full-trim)

Hide 67935 3.INSTALL BACK DOOR SCUFF PLATE (for Full-trim)

Hide 67917C 4.INSTALL REAR DOOR SCUFF PLATE (for Full-trim)

Hide 73560 5.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY (for Full-trim)

a.
B157662C04
2.573,1.073 2.792,1.729 2.792,1.729 3.031,1.052 true 2.708,1.802 3.156,2.146 0.448,0.344 10 *1
*1 Protruding Part


Disconnect the floor anchor plate of the rear No. 2 seat outer belt with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)

NOTICE:

Do not place the floor anchor plate over any of the 2 protruding parts of the floor panel.



Hide 62520P 6.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH (for Semi-trim LH Side)

Hide 62510P 7.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH (for Semi-trim RH Side)

Hide 73431A 8.INSTALL REAR SEAT BELT RETRACTOR COVER (for Semi-trim)

a.

Engage the 4 claws and install the 2 rear seat belt retractor covers.


b.

Install the 4 clips.


Hide 73360C 9.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

a.
B152640C02
0.323,0.948 0.802,1.49 0.802,1.49 0.927,0.948 true 0.729,1.594 1.156,2.031 0.427,0.438 10 *1
*1 Protruding Part


Connect the floor anchor plate of the rear No. 1 seat outer belt assembly with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)

NOTICE:

Do not place the floor anchor plate over the 2 protruding parts of the floor panel.



b.

Connect the shoulder anchor with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)


Hide 73560 10.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY (for Semi-trim)

Hide 73237B 11.INSTALL SHOULDER BELT ANCHOR COVER

a.
B157667

Engage the 2 claws and install the shoulder belt anchor cover.

HINT:

Use the same procedure as for the both the rear No. 1 seat outer belt assembly side and rear No. 2 seat outer assembly side.



Hide 73360C 12.INSPECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

a.

Check that the ELR locks.

NOTICE:
·

The check should be performed with the rear No. 1 seat outer belt installed.

·

Do not allow the anchor part of the rear No. 1 seat outer belt and the protruding parts of the floor panel to overlap.



i.

With the belt installed, check that the belt locks when it is pulled out quickly.

If the operation is not as specified, replace the rear No. 1 seat outer belt assembly.