77377
1.INSTALL FUEL FILLER OPENING LID LOCK RETAINER
Push in the fuel filler opening lid lock retainer.
Rotate the fuel filler opening lid lock retainer by 90° as shown in the illustration.
77035
2.INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
Push in the fuel lid lock control cable sub-assembly to the fuel filler opening lid lock retainer.
Rotate the fuel lid lock control cable sub-assembly by 90° as shown in the illustration.
Engage the 3 clamps and clip, and install the fuel lid lock control cable sub-assembly. (for LHD)
Engage the 3 clamps and clip, and install the fuel lid lock control cable sub-assembly. (for RHD)
77306
3.INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
Install the fuel lid lock control cable sub-assembly to the fuel lid lock open lever sub-assembly.
Install the fuel lid lock open lever sub-assembly with the bolt.
58519C
4.INSTALL REAR WHEEL HOUSE CARPET RH (for Semi-trim)
|
Double Sided Tape |
Apply 4 new pieces of double sided tape as shown in the illustration.
Engage the 2 clips.
62510P
5.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH (for Semi-trim)
Engage the 15 clips and the install the quarter trim front panel assembly RH.
64730B
6.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for Full-trim)
67935
7.INSTALL BACK DOOR SCUFF PLATE
67881A
8.INSTALL BACK DOOR WEATHERSTRIP
62333A
9.INSTALL REAR DOOR OPENING TRIM RH (for Semi-trim)
62414A
10.INSTALL CENTER PILLAR LOWER GARNISH LH (for LHD)
62413A
11.INSTALL CENTER PILLAR LOWER GARNISH RH (for RHD)
Use the same procedure as for the LH side.
67918D
12.INSTALL REAR DOOR SCUFF PLATE LH (for LHD)
67917C
13.INSTALL REAR DOOR SCUFF PLATE RH (for RHD)
Use the same procedure as for the LH side.
67914B
14.INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)
67913B
15.INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)
Use the same procedure as for the LH side.
73560
16.CONNECT REAR NO. 2 OUTER SEAT BELT ASSEMBLY RH (for Semi-trim)
| *1 | Protruding Part |
Connect the floor anchor plate of the rear No. 2 seat outer belt with the bolt.
Do not place the floor anchor plate over any of the 2 protruding parts of the floor panel.
Install the shoulder anchor with the bolt.
73560
17.CONNECT REAR NO. 2 OUTER SEAT BELT ASSEMBLY RH (for Full-trim)
Use the same procedure as for the rear No. 2 seat belt assembly RH (for semi-trim).
73360C
18.CONNECT REAR NO. 1 OUTER SEAT BELT ASSEMBLY RH (for Semi-trim)
| *1 | Protruding Part |
Connect the floor anchor plate of the rear No. 1 seat outer belt assembly with the bolt.
Do not place the floor anchor plate over the 2 protruding parts of the floor panel.
Install the shoulder anchor with the bolt.
73360C
19.CONNECT REAR NO. 1 OUTER SEAT BELT ASSEMBLY RH (for Full-trim)
Use the same procedure as for the rear No. 2 seat belt assembly RH (for semi-trim).
73237B
20.INSTALL SHOULDER BELT ANCHOR COVER (for Semi-trim)
Use the same procedure as 4 shoulder belt anchor covers.
Engage the 2 claws and install the shoulder belt anchor cover.
73431A
21.INSTALL REAR SEAT BELT RETRACTOR COVER (for Semi-trim)
Use the same procedure as 2 rear seat belt retractor covers.
Engage the 2 clips and install the rear seat belt retractor cover.
22.INSTALL REAR NO. 2 SEAT ASSEMBLY
23.INSTALL REAR NO. 1 SEAT ASSEMBLY LH (for LHD)
24.INSTALL REAR NO. 1 SEAT ASSEMBLY RH (for RHD)
25.INSTALL FRONT SEAT ASSEMBLY LH (for LHD)
26.INSTALL FRONT SEAT ASSEMBLY RH (for RHD)