Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2011.11–2015.08
RM19Y0E _58 Vehicle Interior _003015 INTERIOR PANELS / TRIM _0015246 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


PROCEDURE

Hide 63342A 1.INSTALL NO. 2 ROOF SILENCER

a.

Apply adhesive agent to the No. 2 roof silencers.


b.

Attach the 2 new No. 2 roof silencers as shown in the illustration.

B291132C03
3.865,2.729 3.865,3.542 true 5.49,2.708 5.49,3.531 true 3.802,3.583 4.177,3.896 0.375,0.313 10 *1 5.427,3.563 5.74,3.844 0.313,0.281 10 *1
*1 No. 2 Roof Silencer - -
V100135

Front Side - -



Hide 63357B 2.INSTALL ROOF SILENCER

a.

Apply adhesive agent to the roof silencer.


b.

Attach the new roof silencer.

B291134C03
2.01,2.573 2.469,3.948 true 2.427,3.979 2.76,4.344 0.333,0.365 10 *1
*1 Roof Silencer - -
V100135

Front Side - -



Hide 63356B 3.INSTALL ROOF HEADLINING PAD LH (w/ Glass Case)

a.

Apply adhesive agent to the roof headlining pad LH.


b.
B291136C04
1.24,0.688 0.646,0.51 true 1.229,1.5 0.635,1.677 true 0.479,0.406 0.792,0.729 0.313,0.323 10 *1 0.469,1.615 0.833,1.938 0.365,0.323 10 *1
*1 Roof Headlining Pad LH
V100135

Front Side


Attach the 2 new roof headlining pads LH.


Hide 63310 4.INSTALL ROOF HEADLINING ASSEMBLY

a.

Install the roof wiring harness and rear window washer hose as shown in the illustration.

B291116C04
2.094,1 1.698,0.417 true 2.427,3.521 2,4.333 true 4.063,3.635 4.479,4.385 true 1.563,0.26 1.938,0.563 0.375,0.302 10 *1 1.865,4.344 2.198,4.646 0.333,0.302 10 *2 4.521,4.396 4.906,4.74 0.385,0.344 10 *3
*1 Roof Wiring Harness *2 Rear Window Washer Hose
*3 Tape - -



b.

Put the roof headlining in the vehicle through the back door.

NOTICE:

Do not damage the roof headlining assembly or body interior.



c.

Engage the 15 clips (w/ 1 assist grip), 11 clips (w/ 3 assist grips) or 7 clips (w/ 5 assist grips).


d.

Engage the connector and 4 clamps.


e.

Engage the rear window washer hose and 3 clamps.


Hide 74611B 5.INSTALL ASSIST GRIP

HINT:

Use the same procedures for all the assist grip assemblies.


a.

Install the assist grip assembly with 2 screws.


b.

Engage the 2 claws and close the 2 covers.


Hide 6.INSTALL ROOM VENT GRILLE (w/ Rear Air Conditioning System)

a.

Engage the 8 claws and install the room vent grille.


Hide 88570F 7.INSTALL NO. 1 AIR OUTLET GRILLE SUB-ASSEMBLY (w/ Rear Air Conditioning System)

a.

Engage the 10 claws and install the No. 1 air outlet grille sub-assembly.


Hide 74348 8.INSTALL VISOR HOLDER

HINT:

Use the same procedure for both sides.


a.

Engage the 2 claws and install the 2 visor holders.


Hide 74320 9.INSTALL VISOR ASSEMBLY LH

a.

Install the visor assembly LH with screw.


b.

Attach the visor assembly LH shaft into the visor holder.


Hide 74310 10.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 87827 11.INSTALL INNER REAR VIEW MIRROR ABSORBER

a.

Install the inner rear view mirror absorber.


Hide 87810 12.INSTALL INNER REAR VIEW MIRROR

Hide 87834 13.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER

Hide 81240D 14.INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/o Intrusion Sensor)

Hide 81250 15.REMOVE NO. 2 ROOM LIGHT ASSEMBLY (w/ Intrusion Sensor)

Hide 81260A 16.INSTALL MAP LIGHT ASSEMBLY (w/ Glass Case)

Hide 81260A 17.INSTALL MAP LIGHT ASSEMBLY (w/o Glass Case)

Hide 62472D 18.INSTALL REAR PILLAR UPPER GARNISH LH (for Full-trim)

a.

Engage the 3 clips, claw and hook, and install the rear pillar upper garnish LH.


Hide 62471D 19.INSTALL REAR PILLAR UPPER GARNISH RH (for Full-trim)

HINT:

Use the same procedure as for the LH side.


Hide 62639 20.INSTALL REAR QUARTER FRONT TRIM GARNISH LH (for Full-trim)

a.

Engage the 2 clips and claw, and install the rear quarter front trim garnish LH.


Hide 62638 21.INSTALL REAR QUARTER FRONT TRIM GARNISH RH (for Full-trim)

HINT:

Use the same procedure as for the LH side.


Hide 64740C 22.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Full-trim)

a.

Engage the 8 clips and the 6 claws and install the deck trim side panel assembly LH.


Hide 64730B 23.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for Full-trim)

HINT:

Use the same procedure as for the LH side.


Hide 73570 24.INSTALL REAR NO. 2 OUTER SEAT BELT ASSEMBLY LH

a.

Install the shoulder anchor with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)


b.
B157662C06
2.531,0.958 2.479,0.76 true 3.063,0.958 3.083,0.771 true 2.427,0.604 2.813,1 0.385,0.396 10 *1 3.042,0.604 3.385,0.979 0.344,0.375 10 *1
*1 Locating Marks


Install the floor anchor plate with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)

NOTICE:

Do not place the floor anchor plate over the 2 locating marks of the floor panel.



Hide 73560 25.INSTALL REAR NO. 2 OUTER SEAT BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73370C 26.INSTALL REAR NO. 1 OUTER SEAT BELT ASSEMBLY LH

a.

Install the shoulder anchor with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)


b.
B157653C02
2.427,0.927 2.74,1.479 2.74,1.479 3.021,0.927 true 2.677,1.521 3.094,1.917 0.417,0.396 10 *1
*1 Locating Marks


Install the floor anchor plate with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)

NOTICE:

Do not place the floor anchor plate over the 2 locating marks of the floor panel.



Hide 73360C 27.INSTALL REAR NO. 1 OUTER SEAT BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 67881A 28.INSTALL BACK DOOR WEATHERSTRIP

a.

Align the both end of back door weatherstrip within the back door striker mounted point.


Hide 67935 29.INSTALL BACK DOOR SCUFF PLATE

a.

Engage the 4 clips and install the back door scuff plate.


Hide 62412B 30.INSTALL CENTER PILLAR UPPER GARNISH LH

a.

Engage the clip and guide, and install the center pillar upper garnish LH.


Hide 62411B 31.INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73220 32.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (w/o Pretensioner)

a.

Install the front outer seat belt assembly LH with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)


Hide 73210 33.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (w/o Pretensioner)

HINT:

Use the same procedure as for the LH side.


Hide 73220 34.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH (w/ Pretensioner)

a.

Install the front outer seat belt assembly LH with the bolt.

Torque:
41 N*m (413 kgf*cm, 30 ft.*lbf)


Hide 73210 35.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH (w/ Pretensioner)

HINT:

Use the same procedure as for the LH side.


Hide 73237A 36.INSTALL SHOULDER BELT ANCHOR COVER

a.

Install the shoulder anchor cover.


Hide 62212 37.INSTALL FRONT PILLAR GARNISH LH (for 6 Speakers)

Hide 62211 38.INSTALL FRONT PILLAR GARNISH RH (for 6 Speakers)

HINT:

Use the same procedure as for the LH side.


Hide 62212 39.INSTALL FRONT PILLAR GARNISH LH (for 4 Speakers)

Hide 62211 40.INSTALL FRONT PILLAR GARNISH RH (for 4 Speakers)

HINT:

Use the same procedure as for the LH side.


Hide 62334A 41.INSTALL REAR DOOR OPENING TRIM LH (for Full-trim)

a.

Install the rear door opening trim LH.


Hide 62333A 42.INSTALL REAR DOOR OPENING TRIM RH (for Full-trim)

HINT:

Use the same procedure as for the LH side.


Hide 62334A 43.INSTALL REAR DOOR OPENING TRIM LH (for Semi-trim)

HINT:

Use the same procedure as for the rear door opening trim LH (for full-trim) and the rear door opening trim LH (for semi-trim).


Hide 62333A 44.REMOVE REAR DOOR OPENING TRIM RH (for Semi-trim)

HINT:

Use the same procedure as for the LH side.


Hide 62312B 45.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Install the front door opening trim weatherstrip LH.


Hide 62311B 46.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62414A 47.INSTALL CENTER PILLAR LOWER GARNISH LH

a.

Engage the 2 clips and install the center pillar lower garnish LH.


Hide 62413A 48.INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 67918D 49.INSTALL REAR DOOR SCUFF PLATE LH

a.
B297402

Align the 3 bosses of the rear door scuff plate LH with the holes in the body.


b.

Engage the 2 clips and 7 claws and install the rear door scuff plate LH.


Hide 67917C 50.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 67914B 51.INSTALL FRONT DOOR SCUFF PLATE LH

a.
B297403

Align the 2 bosses of the front door scuff plate LH with the holes in the body.


b.

Engage the 9 claws and install the front door scuff plate LH.


Hide 67913B 52.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.