Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015254 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RHD and LHD vehicle.


PROCEDURE

Hide 56111A 1.CLEAN WINDSHIELD GLASS

B112214

a.

Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



b.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:

Do not touch the windshield glass surface after cleaning it.



Hide 56115C 2.INSTALL WINDSHIELD GLASS STOPPER

a.

Using a brush or a sponge, coat the application area of the windshield glass stopper with primer G.

NOTICE:

Do not apply too much primer G.



b.

Install new 2 windshield glass stoppers the windshield glass, as shown in the illustration.

B295646C02
5.563,1.281 5.563,0.667 5.563,0.667 6.729,0.667 true 6.052,1.271 6.052,0.667 true 6.552,1.26 6.552,0.667 true 1.583,1.281 1.583,0.667 1.583,0.667 0.417,0.667 true 1.094,1.271 1.094,0.667 true 0.594,1.26 0.594,0.667 true 0.094,0.042 0.563,0.448 0.469,0.406 10 *a 0.229,0.583 0.667,1 0.438,0.417 10 *b 6.781,0.583 7.094,1 0.313,0.417 10 *b 2.229,1.594 2.635,2.01 0.406,0.417 10 a 4.865,1.594 5.385,2.021 0.521,0.427 10 a 0.76,1.75 1.385,2.302 0.625,0.552 10 b 6.344,1.76 6.719,2.188 0.375,0.427 10 b
*a Back Side *b Ceramic Notch


Standard Dimension:
Area Dimension
a 10.0 to 11.0 mm (0.393 to 0.433 in.)
b 40.0 mm (1.574 in.)



c.

Lightly press the 2 windshield glass stoppers to ensure that the 2 windshield glass stoppers are securely fit to the windshield glass.

HINT:

Press the 2 windshield glass stoppers with a force of 30 N (3.1 kgf, 6.7 lbf) or more.



Hide 56117A 3.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or a sponge, coat the application area of the windshield glass adhesive dam with primer G.

NOTICE:

Do not apply too much primer G.



b.

Install a new adhesive dam onto the windshield glass, as shown in the illustration.

B289328C02
0.854,0.833 1.281,0.594 1.281,0.594 1.719,0.865 true 5.385,0.865 5.76,0.625 5.76,0.625 6.229,0.833 true 1.094,3.927 0.969,4.271 0.969,4.271 1.073,3.854 false 1.208,4.104 0.969,4.271 0.969,4.271 1.146,4.052 false 1.271,4.135 0.969,4.26 false 6.021,3.938 6.146,4.281 6.146,4.281 6.031,3.865 false 5.896,4.094 6.135,4.26 6.135,4.26 5.948,4.042 false 5.844,4.135 6.146,4.271 false 1.135,2.24 0.917,1.927 0.917,1.927 1.094,2.313 true 1.219,2.198 0.927,1.938 false 5.948,2.24 6.167,1.927 6.167,1.927 6,2.313 true 5.885,2.198 6.167,1.938 false 3.188,1.135 3.344,1.354 0.156,0.219 10 A 3.854,2.844 4.01,3.063 0.156,0.219 10 B 3.844,2.479 4,2.698 0.156,0.219 10 B 3.177,1.469 3.333,1.688 0.156,0.219 10 A 2.156,2.135 2.313,2.354 0.156,0.219 10 A 2.51,2.188 2.667,2.406 0.156,0.219 10 A 4.448,1.76 4.604,1.979 0.156,0.219 10 A 4.75,1.719 4.906,1.938 0.156,0.219 10 A 1.344,4.677 1.688,4.865 0.344,0.188 10 A - A 3.719,4.677 4.063,4.865 0.344,0.188 10 B - B 2.219,4.698 2.375,4.854 0.156,0.156 10 a 5.208,4.698 5.406,4.865 0.198,0.167 10 b 0.188,0.094 0.438,0.333 0.25,0.24 10 *a 1.219,0.438 1.469,0.677 0.25,0.24 10 *b 5.688,0.458 5.938,0.698 0.25,0.24 10 *b 0.833,4.271 1.083,4.51 0.25,0.24 10 *b 0.75,1.76 1,2 0.25,0.24 10 *b 6.156,1.74 6.406,1.979 0.25,0.24 10 *b 6.198,4.271 6.448,4.51 0.25,0.24 10 *b
*a Back Side *b Dam Reference Line


Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 50.3 to 54.3 mm (1.980 to 2.137 in.)


NOTICE:

Allow the primer G to dry for 3 minutes or more.



Hide 56111A 4.INSTALL WINDSHIELD GLASS

B221174C04
3.052,2.104 3.313,2.104 false
V100155

Adhesive


a.

Clean and shape the contact surfaces of the vehicle body.

i.

Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.



b.
B270513C05
2.146,0.375 2.833,0.292 2.833,0.292 1.99,0.625 true 2.885,0.167 3.375,0.604 0.49,0.438 10 *a
*a Matchmark


Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the whole contact surface of the windshield glass rim is perfectly even.


iii.

Align the matchmarks on the windshield glass and vehicle body.

NOTICE:

Check that the windshield glass stoppers are attached to the vehicle body correctly.



iv.

Remove the windshield glass.


v.
B295410C04
0.99,0.125 1.469,0.51 0.479,0.385 10 *a 2.521,0.125 3.073,0.479 0.552,0.354 10 *b
*a NG
*b OK
V100145

Primer M
V100155

Adhesive


Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.




vi.

Using a brush, coat the application area of adhesive with primer G.

NOTICE:

Do not apply too much primer G.


B289329C02
0.552,2.906 1.135,3.375 0.583,0.469 10 B 0.896,2.969 1.323,3.313 0.427,0.344 10 B 2.833,2.552 3.271,2.917 0.438,0.365 10 B 3.177,2.5 3.573,2.844 0.396,0.344 10 B 2.271,3.271 2.906,3.729 0.635,0.458 10 C 2.271,3.656 2.646,3.958 0.375,0.302 10 C 2.219,1.906 2.594,2.25 0.375,0.344 10 A 2.219,2.26 2.667,2.646 0.448,0.385 10 A 4.229,0.656 4.99,1.125 0.76,0.469 10 A - A 4.229,2.917 4.917,3.333 0.688,0.417 10 C - C 5.698,0.656 6.375,1.094 0.677,0.438 10 B - B 5.219,1.781 5.771,2.281 0.552,0.5 10 a 6.615,1.865 7.042,2.25 0.427,0.385 10 a 4.917,3.25 5.354,3.635 0.438,0.385 10 b 0.188,0.135 0.969,0.656 0.781,0.521 10 *a
*a Back Side - -
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 12.0 mm (0.472 in.)
b 15.0 mm (0.590 in.)




c.

Cut off the tip of the cartridge nozzle as shown in the illustration.


d.

Load the sealer gun with cartridge.


e.

Apply adhesive to the windshield glass, as shown in the illustration.

B289330C02
0.448,1.167 0.771,0.938 true 4.896,1.635 5.302,0.99 true 6.792,1.604 6.479,1.271 true 5.417,2.792 5.656,2.229 5.656,2.229 5.115,2.792 true 0.281,1.146 0.844,1.615 0.563,0.469 10 *1 0.167,0.083 0.813,0.594 0.646,0.51 10 *a 4.708,1.594 5.135,2.01 0.427,0.417 10 *b 5.667,2.104 6.208,2.563 0.542,0.458 10 *b 6.792,1.635 7.156,1.927 0.365,0.292 10 *b 0.771,2.135 1.281,2.604 0.51,0.469 10 a 3,1.896 3.417,2.271 0.417,0.375 10 A 3,1.552 3.417,1.896 0.417,0.344 10 A 1.677,2.604 2.083,3.042 0.406,0.438 10 B 1.323,2.542 1.667,2.917 0.344,0.375 10 B 3.615,2.198 4.063,2.594 0.448,0.396 10 B 3.958,2.115 4.438,2.573 0.479,0.458 10 B 3.042,3.281 3.552,3.729 0.51,0.448 10 C 3.031,2.917 3.438,3.281 0.406,0.365 10 C 5.24,3.448 5.667,3.771 0.427,0.323 10 a 2.365,3.385 2.854,3.771 0.49,0.385 10 d 4.844,3.125 5.333,3.5 0.49,0.375 10 c 5.615,3.021 6.156,3.438 0.542,0.417 10 c 4.667,0.833 5.26,1.313 0.594,0.479 10 c 5.885,1.25 6.26,1.635 0.375,0.385 10 c 0.677,2.49 1.208,2.938 0.531,0.448 10 a 0.323,1.896 0.833,2.479 0.51,0.583 10 b 4.802,0.188 5.427,0.594 0.625,0.406 10 A - A 4.792,2.073 5.531,2.51 0.74,0.438 10 C - C 6,0.188 6.594,0.604 0.594,0.417 10 B - B 0.323,2.875 0.885,3.344 0.563,0.469 10 b
*1 Sealer Gun - -
*a Back Side *b Adhesive Center Line
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 7.0 mm (0.2756 in.)
b 12.0 mm (0.4724 in.)
c 3.5 mm (0.1575 in.)
d 50.0 mm (1.9685 in.)


NOTICE:

Allow the primer G to dry for 3 minutes or more.



f.
B270513C06
2.146,0.385 2.833,0.302 2.833,0.302 1.99,0.635 true 2.885,0.188 3.344,0.646 0.458,0.458 10 *a
*a Matchmark


Install the windshield glass assembly.

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned, and install the windshield glass.

NOTICE:
·

Allow the primer G to dry for 3 minutes or more.

·

Check that the windshield glass stoppers are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass.




ii.

Lightly press the front surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.



iii.
B159610C09
0.688,1.24 0.375,0.719 false 2.271,1.25 1.958,0.729 false 0.188,0.635 0.927,1.042 0.74,0.406 10 *1 1.771,0.646 2.365,1 0.594,0.354 10 *1
*1 Adhesive


Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Apply adhesive onto the windshield glass rim.



iv.

Hold the windshield glass using protective tape until applied adhesive becomes hard.



Hide 75533E 5.INSTALL WINDSHIELD OUTSIDE MOULDING

B296429C02
1.042,1.469 1.438,1.802 0.396,0.333 10 *a
*a Application Area
V100155

Primer G


a.

Using a brush, coat the application area of the windshield outside moulding with primer G as shown in the illustration.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.



HINT:

If an area that is not specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B291365C02
0.781,0.552 1.26,0.875 false 1.823,0.281 1.552,0.75 false 2.792,0.417 2.375,0.698 false 0.583,0.458 1.125,0.885 0.542,0.427 10 *1 1.823,0.177 2.333,0.573 0.51,0.396 10 *2 2.813,0.302 3.198,0.677 0.385,0.375 10 *3
*1 Windshield Glass
*2 Moulding
*3 Body


Install a new windshield outside moulding as shown in the illustration.


Hide 6.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63310 7.INSTALL ROOF HEADLINING ASSEMBLY

a.

Return the front section of the roof headlining assembly to the original position (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).


Hide 55781E 8.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 85221B 12.INSTALL FRONT WIPER ARM AND BLADE LH

Hide 85211B 13.INSTALL FRONT WIPER ARM AND BLADE RH

Hide 85292B 14.INSTALL FRONT WIPER ARM HEAD CAP