Home › Vehicle Exterior › WINDOW / GLASS › QUARTER WINDOW GLASS
RM19Y0E _59 Vehicle Exterior _003016 WINDOW / GLASS _0015256 QUARTER WINDOW GLASS A

WINDOW / GLASS  QUARTER WINDOW GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Use the same procedure for the RH side and LH side.


PROCEDURE

Hide 62712 1.CLEAN QUARTER WINDOW GLASS LH

a.
B112214

Using a scraper, remove any excess or protruding adhesive sticking to the quarter window glass LH.

NOTICE:

Be careful not to damage the quarter window glass LH.



b.

Clean the outer surface of the quarter window glass LH with a non-residue solvent.

NOTICE:

Even if using a new , clean the with a non-residue solvent.



Hide 75642 2.INSTALL QUARTER WINDOW FRONT OUTSIDE MOULDING LH

a.

Apply primer G to the installation part of the quarter window moulding.

NOTICE:

Do not apply too much primer G.



b.
B295382

Install new quarter window moulding onto the , as shown in the illustration.


Hide 3.INSTALL NO. 1 QUARTER WINDOW GUIDE PIECE PIN

a.

Apply primer G to the installation part of the No. 1 quarter window guide piece pin.

NOTICE:

Do not apply too much primer G.



b.
B300099C02
2.854,0.938 3.219,1.26 0.365,0.323 10 A 3.146,1.344 3.417,1.677 0.271,0.333 10 A 0.292,2.313 0.906,2.688 0.615,0.375 10 A - A 1.708,2.521 2.198,2.917 0.49,0.396 10 *a
*a 40.3 mm (1.586 in.)


Install new No. 1 quarter window guide piece pins onto the quarter window assembly, as shown in the illustration.


Hide 62785A 4.INSTALL QUARTER WINDOW GLASS SPACER

a.
B289335

Apply primer M to the installation part of the quarter window glass spacer.

NOTICE:

Do not apply too much primer M.



b.

Install the new 2 quarter window glass spacer onto the glass LH, as shown in the illustration.


Hide 62712 5.INSTALL QUARTER WINDOW GLASS LH

B221174C06
3.104,2.083 3.323,2.083 false
V100155

Adhesive


a.

Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the outer edge of the quarter window glass LH with a non-residue solvent.



b.

Install the suction cups to the quarter window glass LH.


c.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.


d.
B295410C06
0.99,0.135 1.573,0.5 0.583,0.365 10 *a 2.521,0.135 2.948,0.5 0.427,0.365 10 *b
*a NG
*b OK
V100145

Primer M
V100155

Adhesive


Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.




e.

Using a brush or a sponge, apply primer G or primer M to the quarter window glass LH as shown in illustration.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.



B323669C02
0.281,0.219 0.833,0.604 0.552,0.385 10 *a 2.104,1.833 2.656,2.219 0.552,0.385 10 C 1.875,2.177 2.427,2.563 0.552,0.385 10 C 0.833,2.448 1.385,2.833 0.552,0.385 10 A 0.385,2.552 0.938,2.938 0.552,0.385 10 A 1.604,2.677 2.156,3.063 0.552,0.385 10 B 1.635,3.052 2.188,3.438 0.552,0.385 10 B 2.021,2.729 2.573,3.115 0.552,0.385 10 D 2.271,3.104 2.823,3.49 0.552,0.385 10 D 3.146,0.75 3.917,1.104 0.771,0.354 10 A - A 3.135,2.573 3.906,2.927 0.771,0.354 10 B - B 5.219,2.573 5.99,2.927 0.771,0.354 10 D - D 5.219,0.74 5.99,1.094 0.771,0.354 10 C - C 4.271,1.677 4.677,2 0.406,0.323 10 b 3.823,1.979 4.229,2.302 0.406,0.323 10 a 6.177,1.552 6.583,1.875 0.406,0.323 10 d 6.552,1.583 6.958,1.906 0.406,0.323 10 e 4.115,3.271 4.521,3.594 0.406,0.323 10 d 4.49,3.448 4.896,3.771 0.406,0.323 10 c 6.094,3.448 6.5,3.771 0.406,0.323 10 d 6.25,3.813 6.656,4.135 0.406,0.323 10 f
*a Back Side - -
V100155

Primer G
V100145

Primer M


Standard Dimension:
Area Dimension
a 24.0 mm (0.944 in.)
b 23.0 mm (0.905 in.)
c 25.1 mm (0.988 in.)
d 15.0 mm (0.590 in.)
e 25.0 mm (0.984 in.)
f 25.2 mm (0.992 in.)


i.

Cut off the tip of the cartridge nozzle as shown in the illustration.


ii.

Load the sealer gun with cartridge.


iii.

Apply adhesive to the quarter window glass LH as shown in the illustration.

B323670C02
2.385,3.448 2.646,3 true 0.167,0.115 0.823,0.563 0.656,0.448 10 *a 0.135,1.313 0.615,1.771 0.479,0.458 10 g 0.479,1.542 0.958,2 0.479,0.458 10 A 0.875,1.438 1.354,1.896 0.479,0.458 10 A 2.146,0.875 2.625,1.333 0.479,0.458 10 C 1.917,1.198 2.396,1.656 0.479,0.458 10 C 1.74,1.698 2.219,2.156 0.479,0.458 10 B 1.76,2.073 2.24,2.531 0.479,0.458 10 B 2.073,1.823 2.552,2.281 0.479,0.458 10 D 2.344,2.146 2.823,2.604 0.479,0.458 10 D 0.844,3.531 1.26,3.885 0.417,0.354 10 b 1.354,3.771 1.771,4.125 0.417,0.354 10 a 0.583,3.854 1,4.208 0.417,0.354 10 a 1.094,4.24 1.51,4.594 0.417,0.354 10 b 3.198,0.708 3.938,1.208 0.74,0.5 10 A - A 5.313,0.708 6.052,1.208 0.74,0.5 10 C - C 3.219,2.531 3.958,3.031 0.74,0.5 10 B - B 5.302,2.542 6.042,3.042 0.74,0.5 10 D - D 3.563,1.833 3.979,2.188 0.417,0.354 10 a 4.188,1.844 4.604,2.198 0.417,0.354 10 a 4.583,1.75 5,2.104 0.417,0.354 10 a 3.969,2.115 4.385,2.469 0.417,0.354 10 c 6.219,1.792 6.635,2.146 0.417,0.354 10 a 6.635,1.448 7.052,1.802 0.417,0.354 10 e 4.104,2.979 4.521,3.333 0.417,0.354 10 a 4.542,3.479 4.958,3.833 0.417,0.354 10 d 5.927,3.583 6.344,3.938 0.417,0.354 10 a 6.427,3.833 6.844,4.188 0.417,0.354 10 f 2.688,2.896 3,3.094 0.313,0.198 10 *1
*1 Sealer Gun - -
*a Back Side - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 7.0 mm (0.275 in.)
b 12.0 mm (0.472 in.)
c 35.5 mm (1.397 in.)
d 17.6 mm (0.692 in.)
e 17.5 mm (0.689 in.)
f 17.7 mm (0.696 in.)
g 50.0 mm (1.968 in.)




f.

Install the quarter window glass LH.

i.

Engage the 2 clips to install the quarter window glass LH.


ii.

Lightly press the quarter window glass LH to ensure that the quarter window glass LH is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.




g.
B159610C11
0.698,1.26 0.385,0.74 false 2.271,1.271 1.958,0.75 false 0.198,0.635 0.677,0.958 0.479,0.323 10 *1 1.771,0.646 2.177,0.938 0.406,0.292 10 *1
*1 Adhesive


Using a scraper, remove any excess or protruding adhesive.


h.

Hold the quarter window glass LH in place securely with protective tape or equivalent until the adhesive hardens.


i.

Hold the quarter window glass LH using protective tape until applied adhesive becomes hard.


Hide 6.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 62354A 7.INSTALL QUARTER WINDOW INSIDE TRIM LH (for Semi-trim)

a.

Install the quarter window inside trim LH.


Hide 62639 8.INSTALL REAR QUARTER FRONT TRIM GARNISH LH (for Full-trim)

Hide 62472D 9.INSTALL REAR PILLAR UPPER GARNISH LH (for Full-trim)

Hide 64740C 10.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Full-trim)

Hide 73370C 11.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (for Full-trim)

Hide 73570 12.CONNECT REAR NO. 2 SEAT OUTER BELT LH (for Full-trim)

Hide 67881A 14.INSTALL BACK DOOR WEATHERSTRIP (for Full-trim)

Hide 67935 15.INSTALL BACK DOOR SCUFF PLATE (for Full-trim)

Hide 67918E 16.INSTALL REAR DOOR SCUFF PLATE LH (for Full-trim)