1.REMOVE FRONT SEAT ASSEMBLY LH (for LHD)
2.REMOVE FRONT SEAT ASSEMBLY RH (for RHD)
3.REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for LHD)
4.REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for RHD)
5.REMOVE REAR NO. 2 SEAT ASSEMBLY
73431A
6.REMOVE REAR SEAT BELT RETRACTOR COVER (for Semi-trim)
73237B
7.REMOVE SHOULDER BELT ANCHOR COVER (for Semi-trim)
Use the same procedure as 4 shoulder belt anchor covers.
| *1 | Protective Tape |
Using a screwdriver with its wrapped in protective tape, disengage the 2 claws and remove the shoulder belt anchor cover.
73360C
8.SEPARATE REAR NO. 1 OUTER SEAT BELT ASSEMBLY RH (for Semi-trim)
Remove the bolt and the shoulder anchor.
Remove the bolt and the floor anchor plate.
73360C
9.SEPARATE REAR NO. 1 OUTER SEAT BELT ASSEMBLY RH (for Full-trim)
Remove the bolt and the floor anchor plate.
73560
10.SEPARATE REAR NO. 2 OUTER SEAT BELT ASSEMBLY RH (for Semi-trim)
Remove the bolt and the shoulder anchor.
Remove the bolt and the floor anchor plate.
73560
11.SEPARATE REAR NO. 2 OUTER SEAT BELT ASSEMBLY RH (for Full-trim)
Remove the bolt and the floor anchor plate.
67914B
12.REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)
67913B
13.REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)
Use the same procedure as for the LH side.
67918D
14.REMOVE REAR DOOR SCUFF PLATE LH (for LHD)
67917C
15.REMOVE REAR DOOR SCUFF PLATE RH (for RHD)
Use the same procedure as for the LH side.
62414A
16.REMOVE CENTER PILLAR LOWER GARNISH LH (for LHD)
62413A
17.REMOVE CENTER PILLAR LOWER GARNISH RH (for RHD)
Use the same procedure as for the LH side.
62333A
18.REMOVE REAR DOOR OPENING TRIM RH (for Semi-trim)
67881A
19.REMOVE BACK DOOR WEATHERSTRIP
67935
20.REMOVE BACK DOOR SCUFF PLATE
62510P
21.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH (for Semi-trim)
Disengage the 15 clips and the remove the quarter trim front panel assembly RH.
58519C
22.REMOVE REAR WHEEL HOUSE CARPET RH (for Semi-trim)
Disengage the 2 clips and remove the rear wheel house carpet RH.
64730B
23.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for Full-trim)
77306
24.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
Remove the bolt and the fuel lid lock open lever sub-assembly.
Disconnect the fuel lid lock control cable sub-assembly from the fuel lid lock open lever sub-assembly.
77035
25.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
Disengage the 2 hooks and peel back the front floor mat and rear floor mat. (for LHD)
Disengage the 2 hooks and peel back the front floor mat and rear floor mat. (for RHD)
Rotate the fuel filler opening lid lock retainer by 90° and remove the fuel lid control cable sub-assembly.
Disengage the 3 clamps and clip, and remove the fuel lid lock control cable sub-assembly (for LHD).
Disengage the 3 clamps and clip, and remove the fuel lid lock control cable sub-assembly (for RHD).
77377
26.REMOVE FUEL FILLER OPENING LID LOCK RETAINER
Rotate the fuel filler opening lid lock retainer by 90° and remove the fuel filler opening lid lock retainer.