Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2013.07
RM19Y0E _59 Vehicle Exterior _003017 DOOR / HATCH _0015263 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


PROCEDURE

Hide 67872 1.INSTALL REAR DOOR WEATHERSTRIP

a.
B293525

Engage the 17 clips to install the rear door weatherstrip.


Hide 68640A 2.INSTALL REAR DOOR CHECK ASSEMBLY

a.
B297794C02
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the sliding areas of the rear door check assembly.


b.
B297787

Install the rear door check assembly onto the door panel with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Apply adhesive to the threads of the bolts (body side).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the rear door check assembly onto the body panel with the bolt.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 69340 3.INSTALL REAR DOOR LOCK ASSEMBLY

Hide 4.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B297835C01
1.25,1.844 1.677,1.646 false 1.083,1.781 1.281,2.021 0.198,0.24 10 false *1
*1 Control Rod


Install the rear door outside handle assembly with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Connect the control rod.


Hide 5.INSTALL HOLE PLUG

a.
B293723

Install a new hole plug.


Hide 69804 6.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.

Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly.


b.
B297808C01
2.344,0.375 2.646,0.146 true 2.688,0.021 2.969,0.219 0.281,0.198 10 *1
*1 Temporary Bolt


Install the temporary bolt.


c.

Tighten the 5 bolts and temporary bolt to install the rear door window regulator sub-assembly.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Connect the connector.


Hide 68230C 7.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 68104 8.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B297807

Install the rear door glass sub-assembly onto the rear door window regulator sub-assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 67486B 9.INSTALL REAR DOOR DIVISION BAR SEAL

a.
B365124

Install the rear door division bar seal with the 2 screws.


Hide 67408F 10.INSTALL REAR DOOR REAR LOWER WINDOW GUIDE SUB-ASSEMBLY

a.
B297805

Install the rear door rear lower window guide sub-assembly with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 68152C 11.INSTALL REAR DOOR GLASS RUN

a.
B297804

Install the rear door glass run.


Hide 67842E 12.INSTALL REAR DOOR SERVICE HOLE COVER

a.
B364853C01
0,0 0,0 false
V100145

Rear Door Service Hole Cover
V100143

Butyl Tape


Apply new butyl tape to the door panel, then install a new rear door service hole cover as shown in the illustration.

HINT:
·

Before installing the rear door service hole cover, pull the cables out through the service hole.

·

There should be no wrinkles or folds after attaching the rear door service hole cover.

·

After attaching the rear door service hole cover, check the quality of the seal.




Hide 86160B 13.INSTALL REAR DOOR SPEAKER

Hide 69206C 14.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B297780C01
0.667,0.938 0.375,0.313 true 0.583,1.49 0.354,1.844 true 0.198,0.146 0.552,0.385 0.354,0.24 10 *1 0.156,1.833 0.542,2.083 0.385,0.25 10 *2
*1 Rear Door Lock Remote Control Cable Assembly
*2 Rear Door Inside Locking Cable Assembly


Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.


b.
B365125C01
0.958,1.635 1.167,1.479 true 2.552,1.635 2.677,1.427 true 1.229,1.344 1.542,1.5 0.313,0.156 10 false *1 2.719,1.323 3.031,1.479 0.313,0.156 10 false *2
*1 Claw
*2 Guide


Engage the 2 guides.


c.

Engage the claw and install the rear door inside handle sub-assembly.


Hide 67604 15.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B297802

Engage the 7 clips and install the rear door trim board sub-assembly.


b.

Tighten the 3 screws.


Hide 84810 16.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 74640D 17.INSTALL REAR DOOR ASSIST GRIP ASSEMBLY

a.
B297801

Engage the 9 claws and install the rear door assist grip assembly.


b.

Install the screw.


Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION