Home › Engine / Hybrid System › 3SZ-VE FUEL › FUEL TANK › 2014.04–2015.08
RM19Y0E _51 Engine / Hybrid System _002971 3SZ-VE FUEL _0015014 FUEL TANK A

3SZ-VE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 2.DRAIN FUEL

a.

Remove the drain plug, and drain the fuel into a container.


b.

Clean the drain plug and install it with a new gasket.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 77259C 4.DISCONNECT FUEL HOSE

a.
A142185C01
1.625,1.708 1.885,1.448 false 0.969,1.729 1.229,1.469 false 0.844,1.76 1.156,1.917 0.313,0.156 10 false *1 1.5,1.74 1.813,1.896 0.313,0.156 10 false *2
*1 Fuel Tank To Canister Tube
*2 Fuel Hose


Loosen the hose clamp to disconnect the fuel hose from the fuel tank to canister tube.


Hide 77204A 5.DISCONNECT FUEL TANK RETURN TUBE SUB-ASSEMBLY

a.
A261574C05
2.49,1.708 2.031,2.042 true 2.5,3.24 2.594,2.885 false 1.833,3.313 1.708,2.854 false 2.906,4.104 3.01,3.729 false 0.938,3.375 0.854,3.125 false 1.688,3.781 1.771,4.115 1.771,4.115 1.844,3.781 true 0.979,1.167 1.063,0.885 false 2.521,2.677 2.708,2.833 0.188,0.156 10 false *1 2.802,4.156 2.99,4.313 0.188,0.156 10 false *5 1.698,4.156 1.885,4.313 0.188,0.156 10 false *4 1.625,2.656 1.813,2.813 0.188,0.156 10 false *2 0.75,2.927 0.938,3.083 0.188,0.156 10 false *3 1.844,2.021 2.031,2.177 0.188,0.156 10 false *1 0.865,1.229 1.052,1.385 0.188,0.156 10 false *5
*1 Retainer
*2 Fuel Tube Connector
*3 Nylon Tube
*4 O-ring
*5 Fuel Main Tube
V100135

Pinch
V100136

Pull out


Disengage the 2 claws and push down the retainer as illustrated.


b.

Pull the fuel tank return tube sub-assembly (fuel tube connector) out of the fuel main tube.

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel main tube.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.

·

As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.

·

If the fuel tube connector and fuel main tube are stuck, pinch the fuel main tube and push and pull the fuel tube connector to release them.




Hide 77213B 6.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A142187

Loosen the hose clamp bolt to disconnect the fuel tank to filler pipe hose from the fuel tank inlet pipe sub-assembly.


Hide 77269A 7.DISCONNECT FUEL TANK BREATHER HOSE

a.
A142188

Loosen the hose clamp to disconnect the fuel tank breather hose from the fuel tank inlet pipe sub-assembly.


Hide 77100 8.REMOVE FUEL TANK ASSEMBLY

a.
A142189

Disconnect the fuel pump connector.


b.

Hold the fuel tank assembly using a transmission jack.


c.
A142190

Remove the 4 bolts.


d.

Operate the transmission jack, then remove the fuel tank assembly from the vehicle.


Hide 87268T 9.REMOVE NO. 1 PROTECTOR

a.
A322183

Remove the 2 nuts and No. 1 protector.


Hide 77203A 10.REMOVE FUEL SUCTION TUBE SUB-ASSEMBLY

a.
A322162

Detach the fuel suction tube sub-assembly from the No. 1 fuel tube clamp.


b.
A322163C01
0.667,0.604 1.417,0.25 true 1.167,3.333 0.823,3.021 false 1.823,3.313 1.656,2.938 1.656,2.938 2.052,3.313 true 3.063,3.135 2.729,2.781 false 1.927,4.271 1.927,3.969 false 3.229,4.302 3.229,3.813 false 1.469,0.135 1.781,0.333 0.313,0.198 10 false *1 2.552,2.677 2.865,2.875 0.313,0.198 10 false *1 1.49,2.792 1.802,2.99 0.313,0.198 10 false *2 0.646,2.927 0.958,3.125 0.313,0.198 10 false *3 1.865,4.302 2.177,4.5 0.313,0.198 10 false *4 3.167,4.375 3.313,4.563 0.146,0.188 10 false *5
*1 Retainer
*2 O-ring
*3 Nylon Tube
*4 Fuel Tube Connector
*5 Fuel Pump Tube
V100135

Pinch
V100136

Pull out


Pinch the retainer to unlock it as illustrated, then pull the fuel suction tube sub-assembly (fuel tube connector) out of the fuel pump tube.

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pump tube.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.

·

As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.

·

If the fuel tube connector and fuel pump tube are stuck, pinch the fuel pump tube and push and pull the fuel tube connector to release them.




c.
A322164

Remove the retainer from the fuel pump tube.


d.
A322175

Detach the fuel suction tube sub-assembly from the No. 2 fuel tube clamp.


e.
A322176C01
1.969,0.917 2.76,0.583 true 1.156,3.417 1.458,3.052 false 0.51,4.198 0.708,3.969 false 2.052,3.51 2.354,3.146 false 2.125,4.01 2.281,4.365 2.281,4.365 1.948,4.01 true 2.823,1.115 3.156,0.979 false 2.802,0.469 3.115,0.625 0.313,0.156 10 false *1 2.323,4.385 2.635,4.542 0.313,0.156 10 false *2 2.385,3.01 2.698,3.167 0.313,0.156 10 false *3 0.385,4.25 0.698,4.406 0.313,0.156 10 false *4 1.469,2.917 1.781,3.073 0.313,0.156 10 false *1 3.198,0.865 3.396,1.01 0.198,0.146 10 false *5
*1 Retainer
*2 O-ring
*3 Fuel Tube Connector
*4 Fuel Filter Tube
*5 Nylon Tube
V100135

Pinch
V100136

Pull out


Pinch the retainer to unlock it as illustrated, then pull the fuel suction tube sub-assembly (fuel tube connector) out of the fuel filter tube.

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel filter tube.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.

·

As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.

·

If the fuel tube connector and fuel filter tube are stuck, pinch the fuel filter tube and push and pull the fuel tube connector to release them.




Hide 77204A 11.REMOVE FUEL TANK RETURN TUBE SUB-ASSEMBLY

a.
A322165

Detach the fuel tank return tube sub-assembly from the No. 1 fuel tube clamp.


b.
A322166C01
0.646,0.688 1.51,0.219 true 1.177,3.323 0.833,2.938 false 1.833,3.292 1.677,2.906 false 2.031,3.302 1.688,2.906 false 3.063,3.135 2.688,2.708 false 1.958,4.26 1.958,3.969 false 3.208,4.271 3.208,3.813 false 1.583,0.104 1.896,0.302 0.313,0.198 10 false *1 1.49,2.823 1.802,3.021 0.313,0.198 10 false *2 2.51,2.604 2.823,2.802 0.313,0.198 10 false *1 0.656,2.833 0.969,3.031 0.313,0.198 10 false *3 1.896,4.323 2.208,4.521 0.313,0.198 10 false *4 3.135,4.333 3.292,4.542 0.156,0.208 10 false *5
*1 Retainer
*2 O-ring
*3 Nylon Tube
*4 Fuel Tube Connector
*5 Fuel Pump Tube
V100135

Pinch
V100136

Pull out


Pinch the retainer to unlock it as illustrated, then pull the fuel tank return tube sub-assembly (fuel tube connector) out of the fuel pump tube.

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pump tube.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.

·

As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.

·

If the fuel tube connector and fuel pump tube are stuck, pinch the fuel pump tube and push and pull the fuel tube connector to release them.




c.
A322167

Remove the retainer from the fuel pump tube.


d.
A322177

Detach the fuel tank return tube sub-assembly from the No. 2 fuel tube clamp.


e.
A322178C01
1.573,0.906 2.385,0.906 true 0.458,1.135 0.302,0.979 false 1.375,3.5 1.042,3.146 false 1.323,4.01 1.188,4.365 1.188,4.365 1.51,4.01 true 2.938,4.24 2.729,3.979 false 2.219,3.406 1.885,3.052 false 0.135,0.833 0.448,0.99 0.313,0.156 10 false *5 1.031,4.385 1.344,4.542 0.313,0.156 10 false *2 0.896,2.969 1.208,3.125 0.313,0.156 10 false *3 2.938,4.271 3.25,4.427 0.313,0.156 10 false *4 1.729,2.875 2.042,3.031 0.313,0.156 10 false *1 2.448,0.813 2.76,0.969 0.313,0.156 10 false *1
*1 Retainer
*2 O-ring
*3 Fuel Tube Connector
*4 Fuel Filter Tube
*5 Nylon Tube
V100135

Pinch
V100136

Pull out


Pinch the retainer to unlock it as illustrated, then pull the fuel tank return tube sub-assembly (fuel tube connector) out of the fuel filter tube.

NOTICE:
·

Remove any dirt and foreign matter from the fuel tube connector.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel filter tube.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected parts by covering them with a plastic bag after disconnecting the fuel tube connector.

·

As some pressure remains in the fuel line, use a piece of cloth to prevent gasoline from splashing out.

·

If the fuel tube connector and fuel filter tube are stuck, pinch the fuel filter tube and push and pull the fuel tube connector to release them.




Hide 77285D 12.REMOVE NO. 1 FUEL TUBE CLAMP

a.
A322179

Disengage the 2 claws to remove the No. 1 fuel tube clamp from the fuel tank assembly.


Hide 77286D 13.REMOVE NO. 2 FUEL TUBE CLAMP

a.
A322182

Disengage the guide to remove the No. 2 fuel tube clamp from the fuel tank assembly as shown in the illustration.


Hide 23210P 14.REMOVE FUEL PUMP WITH MOTOR AND BRACKET ASSEMBLY

Hide 23300J 15.REMOVE FUEL FILTER ASSEMBLY

A325607

a.

Remove the 2 bolts and fuel filter assembly.


Hide 77213B 16.REMOVE FUEL TANK TO FILLER PIPE HOSE

A142194

a.

Loosen the hose clamp bolt to remove the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77269A 17.REMOVE FUEL TANK BREATHER HOSE

A142195

a.

Loosen the hose clamp to disconnect the fuel tank breather hose from the fuel tank assembly.


Hide 77108B 18.REMOVE FUEL TANK FILLER CHECK VALVE SUB-ASSEMBLY

A142196

a.

Remove the fuel tank filler check valve sub-assembly from the fuel tank assembly.


Hide 77631A 19.REMOVE CENTER LOWER FUEL TANK PROTECTOR

a.
A142197

Remove the 3 bolts and center lower fuel tank protector.


Hide 77100B 20.REMOVE FUEL HOSE CLAMP

a.
A142199

Disengage the 4 claws to remove the fuel hose clamp from the fuel tank assembly.


Hide 77013 21.REMOVE NO. 2 FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.
A325608

Detach the No. 2 fuel tank breather tube sub-assembly from the fuel tank assembly.


b.
A142200

Remove the 4 bolts and No. 2 fuel tank breather tube sub-assembly.


Hide 77380 22.REMOVE FUEL CUT OFF VALVE ASSEMBLY

a.
A142201

Remove the fuel cut off valve assembly from the fuel tank assembly.


Hide 77141B 23.REMOVE NO. 1 FUEL TANK FLANGE REINFORCEMENT

A261203

a.

Remove the 4 No. 1 fuel tank flange reinforcements from the fuel tank assembly.


Hide 77201 24.REMOVE FUEL TANK INLET PIPE SUB-ASSEMBLY

A285399

a.

Remove the fuel tank cap assembly.


b.

Remove the 2 bolts, then pull the fuel tank inlet pipe sub-assembly out of the fuel tank filler pipe shield.