Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Steering ECU Communication Stop Mode Either condition is met:
·

"EPS" is not displayed on the CAN Bus Check screen of the GTS or Techstream

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Power steering ECU assembly branch line or connector

·

Power source circuit of power steering ECU assembly

·

Power steering ECU assembly ground circuit

·

Power steering ECU assembly



WIRING DIAGRAM

C329965E02
2.073,0.927 1.917,0.333 1.917,0.333 1.75,0.333 false 4.313,0.927 4.583,0.333 4.583,0.333 4.75,0.333 false 3.365,4.302 5.448,4.708 2.083,0.406 10 false Power Steering ECU Assembly 3.625,3.281 4.146,3.552 0.521,0.271 10 false BAT+ 2.542,3.448 3.021,3.708 0.479,0.26 10 false EPS 3.906,2.958 4.365,3.25 0.458,0.292 10 false CANH 4.396,2.958 4.854,3.25 0.458,0.292 10 false CANL 1.469,4.938 3.438,5.313 1.969,0.375 10 false : CAN Main Bus Line (CANH) 1.49,5.24 3.458,5.615 1.969,0.375 10 false : CAN Main Bus Line (CANL) 4.417,4.938 6.385,5.313 1.969,0.375 10 false : CAN Branch Line (CANH) 4.417,5.229 6.385,5.604 1.969,0.375 10 false : CAN Branch Line (CANL) 5.844,3.604 6.76,3.969 0.917,0.365 10 false Trouble Area 4.698,3.469 5.094,3.698 0.396,0.229 10 false GND 0.688,2.5 1.146,2.792 0.458,0.292 10 false ECM 5.802,2.49 7.01,3.177 1.208,0.688 10 false Combination Meter Assembly 3.167,0.229 3.625,0.521 0.458,0.292 10 false DLC3 0.354,0.24 1.729,0.917 1.375,0.677 10 false Main Body ECU (Fuse Block Assembly) 4.833,0.25 6.875,0.635 2.042,0.385 10 false No. 1 CAN Junction Connector 3.365,3.094 3.615,3.313 0.25,0.219 10 false 1 3.802,2.719 4.052,2.938 0.25,0.219 10 false 5 4.719,2.719 4.969,2.938 0.25,0.219 10 false 1 5.167,3.281 5.417,3.5 0.25,0.219 10 false 2 3.281,3.281 3.698,3.542 0.417,0.26 10 false E74 3.99,2.719 4.406,2.979 0.417,0.26 10 false E75 4.385,2.719 4.802,2.979 0.417,0.26 10 false E75 5.083,3.479 5.5,3.74 0.417,0.26 10 false E74 0.688,1.875 1.146,2.167 0.458,0.292 10 false 120 Ω 6.125,1.885 6.583,2.177 0.458,0.292 10 false 120 Ω 3.635,3.75 3.969,4.01 0.333,0.26 10 false IG 3.281,3.74 3.698,4 0.417,0.26 10 false E75 2.438,3.885 3.125,4.167 0.688,0.281 10 false ECU-IG1 3.365,3.542 3.615,3.76 0.25,0.219 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 3 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the E75 power steering ECU assembly connector.


c.
C329957C03
1.479,0.26 1.896,0.51 0.417,0.25 1.427,1.156 1.083,0.833 1.083,0.833 0.917,0.833 true 1.417,1.458 1.083,1.833 1.083,1.833 0.917,1.833 true 1.573,0.302 1.969,0.552 0.396,0.25 10 false E75 0.104,0.094 0.5,0.344 0.396,0.25 10 false *a 0.5,0.771 1,1.063 0.5,0.292 10 false CANL 0.479,1.76 0.979,2.052 0.5,0.292 10 false CANH
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E75-5 (CANH) - E75-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (POWER STEERING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the E74 power steering ECU assembly connector.


b.
C329968C04
1.5,0.323 1.917,0.573 0.417,0.25 2.063,1.292 2.313,0.75 2.313,0.75 2.5,0.75 true 0.094,0.104 0.417,0.396 0.323,0.292 10 false *a 1.583,0.365 1.958,0.604 0.375,0.24 10 false E74 2.563,0.677 3.042,0.938 0.479,0.26 10 false GND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E74-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.
C332397C04
1.49,2.771 1.906,3.021 0.417,0.25 1.479,0.5 1.896,0.75 0.417,0.25 1.417,3.75 1.167,4.25 1.167,4.25 1,4.25 true 2,1.573 2.333,1.24 2.333,1.24 2.5,1.24 true 0.094,0.094 0.469,0.448 0.375,0.354 10 false *a 1.573,2.813 1.99,3.104 0.417,0.292 10 false E74 1.563,0.542 1.979,0.833 0.417,0.292 10 false E75 0.583,4.167 1.083,4.458 0.5,0.292 10 false BAT+ 2.552,1.156 3.052,1.448 0.5,0.292 10 false IG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E74-1 (BAT+)- Body ground Always 11 to 14 V
E75-8 (IG)- Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)