Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

"Airbag" is not displayed on the CAN Bus Check screen of the GTS or Techstream

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Airbag ECU assembly branch line or connector

·

Power source circuit of airbag ECU assembly

·

Airbag ECU Assembly ground circuit

·

Airbag ECU assembly



WIRING DIAGRAM

C329969E02
2.083,0.917 1.917,0.25 1.917,0.25 1.75,0.25 false 4.583,0.917 4.75,0.25 4.75,0.25 4.917,0.25 false 3.729,4.302 5.323,4.667 1.594,0.365 10 false Airbag ECU Assembly 3.406,4.302 3.802,4.604 0.396,0.302 10 false E76 2.448,3.646 3.083,3.927 0.635,0.281 10 false ECU-IG1 1.448,4.927 3.323,5.281 1.875,0.354 10 false : CAN Main Bus Line (CANH) 1.448,5.24 3.323,5.594 1.875,0.354 10 false : CAN Main Bus Line (CANL) 4.438,4.938 6.313,5.292 1.875,0.354 10 false : CAN Branch Line (CANH) 4.438,5.219 6.313,5.573 1.875,0.354 10 false : CAN Branch Line (CANL) 0.344,0.167 1.719,0.833 1.375,0.667 10 false Main Body ECU (Fuse Block Assembly) 5.021,0.177 7.01,0.563 1.99,0.385 10 false No. 1 CAN Junction Connector 3.156,0.208 3.792,0.49 0.635,0.281 10 false DLC3 0.719,2.49 1.354,2.771 0.635,0.281 10 false ECM 5.771,2.49 6.969,3.177 1.198,0.688 10 false Combination Meter Assembly 3.854,2.938 4.354,3.25 0.5,0.313 10 false CANH 4.385,2.938 4.885,3.25 0.5,0.313 10 false CANL 4.813,3.479 5.146,3.76 0.333,0.281 10 false E1 3.646,3.49 4.115,3.802 0.469,0.313 10 false IG1 3.375,3.375 3.708,3.656 0.333,0.281 10 false 10 3.885,2.708 4.146,2.958 0.26,0.25 10 false 26 4.563,2.708 4.823,2.958 0.26,0.25 10 false 25 5.063,3.375 5.396,3.656 0.333,0.281 10 false 16 5.854,3.667 6.823,3.969 0.969,0.302 10 false Trouble Area 6.104,1.896 6.74,2.177 0.635,0.281 10 false 120 Ω 0.677,1.875 1.313,2.156 0.635,0.281 10 false 120 Ω

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 6 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIRBAG ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the E76 airbag ECU assembly connector.


c.
C329959C05
1.531,0.417 1.948,0.667 0.417,0.25 2.615,1.552 2.656,1.875 2.656,1.875 2.823,1.875 true 2.438,1.542 2.375,1.885 2.375,1.885 2.208,1.885 true 0.104,0.115 0.438,0.417 0.333,0.302 10 false *a 1.615,0.458 1.969,0.698 0.354,0.24 10 false E76 2.885,1.792 3.375,2.063 0.49,0.271 10 false CANH 1.792,1.802 2.281,2.073 0.49,0.271 10 false CANL
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E76-26 (CANH) - E76-25 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (AIRBAG ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C329959C06
1.531,0.417 1.948,0.667 0.417,0.25 0.875,1.552 0.813,1.896 0.813,1.896 0.646,1.896 true 0.104,0.115 0.438,0.417 0.333,0.302 10 false *a 1.615,0.458 1.969,0.698 0.354,0.24 10 false E76 0.385,1.823 0.771,2.094 0.385,0.271 10 false E1
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E76-16 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C329959C07
1.531,0.417 1.948,0.667 0.417,0.25 1.313,1.229 1.063,0.563 1.063,0.563 0.896,0.563 true 0.104,0.115 0.438,0.417 0.333,0.302 10 false *a 1.625,0.458 1.979,0.698 0.354,0.24 10 false E76 0.615,0.5 0.948,0.75 0.333,0.25 10 false IG1
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E76-10 (IG1)- Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)