63342A
1.INSTALL NO. 2 ROOF SILENCER
Apply adhesive agent to 2 new No. 2 roof silencers.
Attach the 2 new No. 2 roof silencers as shown in the illustration.
| *1 | No. 2 Roof Silencer | - | - |
| *a | Align | - | - |
|
Front Side | - | - |
63357B
2.INSTALL ROOF SILENCER
Apply adhesive agent to a new roof silencer.
Attach the new roof silencer as shown in the illustration.
| *1 | Roof Silencer | - | - |
| *a | Align | - | - |
|
Front Side | - | - |
63352C
3.INSTALL ROOF HEADLINING END PAD (for Full-trim)
| *1 | Roof Headlining End Pad |
|
Rear Side |
Apply adhesive agent to 2 new roof headlining end pads.
Attach the 2 new roof headlining end pads.
63356B
4.INSTALL ROOF HEADLINING PAD LH (w/ Glass Case)
Apply adhesive agent to 2 new roof headlining pads LH.
| *1 | Roof Headlining Pad LH |
|
Front Side |
Attach the 2 new roof headlining pads LH.
63310
5.INSTALL ROOF HEADLINING ASSEMBLY
Install the roof wiring harness as shown in the illustration.
Install the rear window washer hose as shown in the illustration (w/ Rear Wiper).
| *1 | Roof Wiring Harness | *2 | Rear Window Washer Hose |
| *3 | Tape | - | - |
Put the roof headlining in the vehicle through the back door.
Do not damage the roof headlining assembly or body interior.
Connect the rear washer hose (w/ Rear Wiper).
w/o Rear Air Conditioning System:
Install the 15 clips (w/ 1 assist grip) or 11 clips (w/ 3 assist grips).
| *a | for RHD | *b | for LHD |
| *c | w/ 1 assist grip | *d | w/ 1 or 3 assist grips |
| *e | w/ 3 assist grips | - | - |
|
Front Side | - | - |
w/ Rear Air Conditioning System:
Install the 11 clips.
| *a | for RHD | *b | for LHD |
|
Front Side | - | - |
Connect the connector and engage the 4 clamps.
w/ Rear Wiper:
Connect the rear window washer hose and engage the 3 clamps.
6.INSTALL ASSIST GRIP ASSEMBLY
Use the same procedures for all the assist grip assemblies.
Install the assist grip assembly with the 2 screws.
Engage the 2 claws to close the 2 covers.
62961C
7.INSTALL ROOM VENT GRILLE (w/ Rear Air Conditioning System)
Engage the 8 claws to install the room vent grille.
8.INSTALL NO. 1 AIR OUTLET GRILLE SUB-ASSEMBLY (w/ Rear Air Conditioning System)
Connect the connector.
Engage the 10 claws to install the No. 1 air outlet grille sub-assembly.
74348
9.INSTALL VISOR HOLDER
Engage the 2 claws to install the visor holder.
Use the same procedure for both sides.
74320
10.INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the screw.
Engage the visor shaft into the visor holder.
74310
11.INSTALL VISOR ASSEMBLY RH
Use the same procedure as for the LH side.
87827
12.INSTALL INNER REAR VIEW MIRROR ABSORBER
Install the inner rear view mirror absorber.
87810
13.INSTALL INNER REAR VIEW MIRROR
87834
14.INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER
81240D
15.INSTALL NO. 2 ROOM LIGHT ASSEMBLY
81260A
16.INSTALL MAP LIGHT ASSEMBLY (w/ Glass Case)
81260A
17.INSTALL MAP LIGHT ASSEMBLY (w/o Glass Case)
58519C
18.INSTALL REAR WHEEL HOUSE CARPET RH (for Semi-trim)
|
Double Sided Tape |
Apply 4 new pieces of double sided tape as shown in the illustration.
Install the rear wheel house carpet RH with the 2 clips.
58529C
19.INSTALL REAR WHEEL HOUSE CARPET LH (for Semi-trim)
Use the same procedure as for the RH side.
62510P
20.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH (for Semi-trim)
Engage the 15 clips to install the front quarter trim panel assembly RH.
62520P
21.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH (for Semi-trim)
Engage the 13 clips to install the front quarter trim panel assembly LH.
62472D
22.INSTALL REAR PILLAR UPPER GARNISH LH (for Full-trim)
Engage the 3 clips, claw and hook to install the rear pillar upper garnish LH.
62471D
23.INSTALL REAR PILLAR UPPER GARNISH RH (for Full-trim)
Use the same procedure as for the LH side.
62639
24.INSTALL REAR QUARTER FRONT TRIM GARNISH LH (for Full-trim)
Engage the 2 clips and claw to install the rear quarter front trim garnish LH.
62638
25.INSTALL REAR QUARTER FRONT TRIM GARNISH RH (for Full-trim)
Use the same procedure as for the LH side.
64740C
26.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for Full-trim)
Engage the 8 clips and 6 claws to install the deck trim side panel assembly LH.
64730B
27.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for Full-trim)
Use the same procedure as for the LH side.
73137A
28.INSTALL UPPER SHOULDER BELT ANCHOR COVER (w/ Rear No. 1 Outer Seat Belt)
Engage the guide, 3 clips and 6 claws to install the upper shoulder belt anchor cover.
73570
29.INSTALL REAR NO. 2 OUTER SEAT BELT ASSEMBLY LH (w/ Rear No. 2 Outer Seat Belt)
Install the shoulder anchor with the bolt.
| *1 | Locating Marks |
Install the floor anchor plate with the bolt.
Do not place the floor anchor plate over the 2 locating marks of the floor panel.
73560
30.INSTALL REAR NO. 2 OUTER SEAT BELT ASSEMBLY RH (w/ Rear No. 2 Outer Seat Belt)
Use the same procedure as for the LH side.
73370C
31.INSTALL REAR NO. 1 OUTER SEAT BELT ASSEMBLY LH (w/ Rear No. 1 Outer Seat Belt)
Install the shoulder anchor with the bolt.
| *1 | Locating Marks |
Install the floor anchor plate with the bolt.
Do not place the floor anchor plate over the 2 locating marks of the floor panel.
73360C
32.INSTALL REAR NO. 1 OUTER SEAT BELT ASSEMBLY RH (w/ Rear No. 1 Outer Seat Belt)
Use the same procedure as for the LH side.
73237B
33.INSTALL SHOULDER BELT ANCHOR COVER
Use the same procedure for all the shoulder belt anchor covers.
Engage the 2 claws to install the shoulder anchor cover.
67935
34.INSTALL BACK DOOR SCUFF PLATE
Engage the 4 clips to install the back door scuff plate.
67881A
35.INSTALL BACK DOOR WEATHERSTRIP
Align both ends of the back door weatherstrip within the back door striker mounted point and install the back door weatherstrip.
62412B
36.INSTALL CENTER PILLAR UPPER GARNISH LH
Engage the clip and guide to install the center pillar upper garnish LH.
62411B
37.INSTALL CENTER PILLAR UPPER GARNISH RH
Use the same procedure as for the LH side.
73220
38.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH
Install the front seat outer belt assembly LH with the bolt.
Engage the 2 claws to close the shoulder belt anchor cover.
73210
39.INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62212
40.INSTALL FRONT PILLAR GARNISH LH (for 6 Speakers)
62211
41.INSTALL FRONT PILLAR GARNISH RH (for 6 Speakers)
Use the same procedure as for the LH side.
62212
42.INSTALL FRONT PILLAR GARNISH LH (for 4 Speakers)
Use the same procedure as for the front pillar garnish LH (for 6 Speakers).
62211
43.INSTALL FRONT PILLAR GARNISH RH (for 4 Speakers)
Use the same procedure as for the LH side.
62334A
44.INSTALL REAR DOOR OPENING TRIM LH (for Full-trim)
Install the rear door opening trim LH.
62333A
45.INSTALL REAR DOOR OPENING TRIM RH (for Full-trim)
Use the same procedure as for the LH side.
62334A
46.INSTALL REAR DOOR OPENING TRIM LH (for Semi-trim)
Use the same procedure as for the rear door opening trim LH (for full-trim).
62333A
47.INSTALL REAR DOOR OPENING TRIM RH (for Semi-trim)
Use the same procedure as for the LH side.
62312B
48.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Install the front door opening trim weatherstrip LH.
62311B
49.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62414A
50.INSTALL CENTER PILLAR LOWER GARNISH LH
Install the center pillar lower garnish LH.
62413A
51.INSTALL CENTER PILLAR LOWER GARNISH RH
Use the same procedure as for the LH side.
67918D
52.INSTALL REAR DOOR SCUFF PLATE LH
Align the 3 bosses of the rear door scuff plate LH with the holes in the body.
Engage the 2 clips and 7 claws to install the rear door scuff plate LH.
67917C
53.INSTALL REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
67914B
54.INSTALL FRONT DOOR SCUFF PLATE LH
Align the 2 bosses of the front door scuff plate LH with the holes in the body.
Engage the 9 claws to install the front door scuff plate LH.
67913B
55.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.