Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042271 1NR-VE ENGINE CONTROL _0196149 SFI SYSTEM C

1NR-VE ENGINE CONTROL  SFI SYSTEM  U0167  Communication with Immobilizer System  


DESCRIPTION

The transponder key ECU assembly ensures security by controlling the START/END of the communication of matching codes with the ECM. It does so in accordance with the ignition ON/OFF status and the immobiliser SET/UNSET status.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0167 Communication with Immobilizer System Communication problem with transponder key ECU assembly or code mismatch
(1 trip detection logic)
·

Engine immobiliser system

·

Transponder key ECU assembly

·

Open or short in communication line (wire harness or connector)

·

ECM


- DTC stored

HINT:

This DTC is output when: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; and 3) the ECU communication IDs between the transponder key ECU assembly and the ECM are different when an engine start is attempted.


WIRING DIAGRAM

PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC U0167)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Enter the following menus: Powertrain / EFI / Trouble codes.


j.

Read the DTCs.

HINT:

If any transponder key ECU assembly DTC is present, refer to its inspection procedure first.



Result:
Result Proceed to
DTCs are not output A
DTC U0167 and other DTCs are output (engine cannot start) B
DTC U0167 is output (engine cannot start) C



A

B

C

2.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ECM - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
A24-54 (SIO2) - E58-9 (SIO2) Always Below 1 Ω
A24-54 (SIO2) or E58-9 (SIO2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.PERFORM KEY REGISTRATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.PERFORM KEY REGISTRATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Reregister the key (key ID code).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / EFI / Trouble codes.


f.

Read the DTCs.


Result:
Result Proceed to
DTCs are not output (engine start) A
DTC U0167 is output (engine cannot start) B



A

END

B

5.REPLACE ECM
5.REPLACE ECM
a.

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / EFI / Trouble codes.


f.

Read the DTCs.


Result:
Result Proceed to
DTCs are not output (engine start) A
DTC U0167 is output (engine cannot start) B



A

END

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY