Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042271 1NR-VE ENGINE CONTROL _0196149 SFI SYSTEM C

1NR-VE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor System Open/Low  P0328  Knock Sensor System Open/High  


DESCRIPTION

A flat type knock control sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.

The knock control sensor is fitted onto the engine block to detect engine knocking.

The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0327 Knock Sensor System Open/Low The output voltage of the knock control sensor is less than 0.5 V for 1 second or more (1 trip detection logic).
·

Short in knock control sensor circuit

·

Knock control sensor

·

ECM


Comes on DTC stored
P0328 Knock Sensor System Open/High The output voltage of the knock control sensor is higher than 4.5 V for 1 second or more (1 trip detection logic).
·

Open in knock control sensor circuit

·

Knock control sensor

·

ECM


Comes on DTC stored

HINT:

When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A283572E08
2.365,0.521 3.094,0.75 0.729,0.229 10 1 V/DIV. 2.604,1 3,1.229 0.396,0.229 10 GND 1.115,1.844 1.906,2.083 0.792,0.24 10 1 ms./DIV.

The correct waveform is as shown.

ECM Terminal Name Between KNK and E2
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 5 minutes.

7.

Enter the following menus: Powertrain / EFI / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A298569E03
5.49,1.146 6.104,1.344 0.615,0.198 10 false KNK 5.479,1.958 6.094,2.156 0.615,0.198 10 false E2 6.042,3.354 6.656,3.552 0.615,0.198 10 false ECM 5.646,3.354 6.26,3.552 0.615,0.198 10 false C50 0.458,3.323 1.26,3.552 0.802,0.229 10 false *:Shielded 5.135,1.958 5.75,2.156 0.615,0.198 10 false 100 5.135,1.135 5.75,1.333 0.615,0.198 10 false 106 2.698,1.135 3.063,1.333 0.365,0.198 10 false 2 1.01,1.135 1.375,1.333 0.365,0.198 10 false 1 1.125,1.656 1.438,1.854 0.313,0.198 10 false C13 1.406,1.656 4.469,1.854 3.063,0.198 10 false Knock Control Sensor 2.479,1.135 2.635,1.333 0.156,0.198 10 false + 1.229,1.125 1.385,1.323 0.156,0.198 10 false - 3.844,2.51 4,2.708 0.156,0.198 10 false *

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (KNOCK CONTROL VALUE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / EFI / Data List / Knock control value.


f.

Read the value while driving the vehicle.

OK:

The value changes.


HINT:
Malfunction does not occur Knock control value changes
Malfunctions occur Knock control value does not change

The Knock control value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
a.
A288761C02
0.5,2.083 0.833,2.333 0.333,0.25 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 0.552,2.115 0.865,2.313 0.313,0.198 10 false C13
*a Front view of wire harness connector
(to Knock Control Sensor)


Disconnect the knock control sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C13-2(+) - C13-1(-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT KNOCK CONTROL SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
3.INSPECT KNOCK CONTROL SENSOR
a.

Inspect the knock control sensor.

Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>KNOCK SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
a.

Disconnect the knock control sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C13-2(+) - C50-106 (KNK) Always Below 1 Ω
C13-1(-) - C50-100 (E2) Always Below 1 Ω
C13-2(+) or C50-106 (KNK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR