Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042271 1NR-VE ENGINE CONTROL _0196149 SFI SYSTEM C

1NR-VE ENGINE CONTROL  SFI SYSTEM  P0504  Stop Lamp Switch System Malfunction  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop lamp SW and ST1 input flag are ON when the brake pedal is depressed because the ST1 input flag indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Stop Lamp Switch System Malfunction Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON
(b) STP signal OFF when ST1- signal OFF
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A372323E01
0.021,1.49 1.25,1.917 1.229,0.427 10 false to No. 1 Integration Relay 1.583,1.667 2.25,1.917 0.667,0.25 10 false ECU IG2 2.51,1.375 2.667,1.573 0.156,0.198 10 false 3 2.74,1.385 3.031,1.583 0.292,0.198 10 false CR1 3.833,1.385 3.99,1.583 0.156,0.198 10 false 4 3.427,1.385 3.76,1.563 0.333,0.177 10 false CR2 2.51,2.052 2.667,2.25 0.156,0.198 10 false 1 3.833,2.052 3.99,2.25 0.156,0.198 10 false 2 2.75,2.135 2.906,2.333 0.156,0.198 10 false + 3.594,2.135 3.75,2.333 0.156,0.198 10 false - 2.688,2.531 3.146,2.729 0.458,0.198 10 false E69 2.677,2.688 3.76,3.052 1.083,0.365 10 false Stop Light Switch Assembly 2.333,3.167 2.646,3.365 0.313,0.198 10 false 3E 2.25,2.969 2.563,3.167 0.313,0.198 10 false 18 4,3.167 4.313,3.365 0.313,0.198 10 false 3E 3.854,2.969 4.167,3.167 0.313,0.198 10 false 10 4.875,4.01 5.188,4.208 0.313,0.198 10 false 3D 4.927,3.833 5.083,4.031 0.156,0.198 10 false 9 2.219,3.719 2.667,3.917 0.448,0.198 10 false STPH 3.917,3.719 4.333,3.917 0.417,0.198 10 false STPL 4,4 4.417,4.167 0.417,0.167 10 false STPO 1.969,4.469 4.417,4.75 2.448,0.281 10 false Main Body ECU (Fuse Block Assembly) 6.042,4.417 6.333,4.583 0.292,0.167 10 false A24 6.333,4.417 6.708,4.583 0.375,0.167 10 false ECM 5.667,1.375 5.865,1.604 0.198,0.229 10 false 62 5.99,1.5 6.417,1.729 0.427,0.229 10 false ST1- 5.688,3.885 5.917,4.083 0.229,0.198 10 false 48 5.958,4 6.333,4.167 0.375,0.167 10 false STP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / EFI / Data List / Stop lamp SW and ST1 input flag.

5.

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop lamp SW ST1 input flag
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A203090C30
0.531,2.073 0.906,2.333 0.375,0.26 0.917,2.948 1.333,2.531 true 0.229,0.167 0.542,0.365 0.313,0.198 10 false *a 0.594,2.115 0.906,2.313 0.313,0.198 10 false E69 0.781,2.969 1.115,3.167 0.333,0.198 10 false CR1
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E69-3(CR1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECU IG2 RELAY)

2.CHECK HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - MAIN BODY ECU (FUSE BLOCK ASSEMBLY))
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the main body ECU (fuse block assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3E-18 (STPH) - E69-1 (+) Always Below 1 Ω
3E-10 (STPL) - E69-2 (-) Always Below 1 Ω
3E-18 (STPH) or E69-1 (+) - Body ground Always 10 kΩ or higher
3E-10 (STPL) or E69-2 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E69-4 (CR2) - A24-62 (ST1-) Always Below 1 Ω
E69-4 (CR2) or A24-62 (ST1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TERMINAL VOLTAGE (STP VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

5.CHECK TERMINAL VOLTAGE (STP VOLTAGE)
a.

Disconnect the ECM connector.

A361578C04
4.083,0.75 4.49,1 0.406,0.25 5.802,1.552 5.594,1.073 true 0.615,0.167 0.927,0.365 0.313,0.198 10 false *a 2.26,0.156 2.573,0.354 0.313,0.198 10 false *b 4.385,0.167 4.698,0.365 0.313,0.198 10 false *c 5.844,1.49 6.198,1.688 0.354,0.198 10 false STP 4.156,0.792 4.615,0.99 0.458,0.198 10 false A24
*a Brake Pedal Depressed *b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)
- -



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-48 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - ECU)