Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042271 1NR-VE ENGINE CONTROL _0196149 SFI SYSTEM C

1NR-VE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STSW of the ECM.

If the ECM detects the starter signal while the vehicle is being driven, it determines that there is a malfunction in the starter signal circuit. The ECM then illuminates the MIL and stores this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High All of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

Starter signal circuit

·

No. 1 integration relay

·

Ignition or starter switch assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A231469E19
1.229,1.979 1.667,2.25 0.438,0.271 10 Idling 0.438,2.26 1.583,2.5 1.146,0.24 10 Ignition Switch ON 0.438,0.844 1.583,1.083 1.146,0.24 10 24 km/h (15 mph) 2.396,2.865 3.063,3.292 0.667,0.427 10 5 seconds or more 3.635,2.938 4.917,3.167 1.281,0.229 10 20 seconds or more 2.031,2.333 2.271,2.563 0.24,0.229 10 [A] 2.635,2.104 2.917,2.365 0.281,0.26 10 [B] 4.063,0.469 4.313,0.708 0.25,0.24 10 [C] 4.896,3.313 5.167,3.583 0.271,0.271 10 [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Idle the engine for 5 seconds or more [B].

8.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / EFI / Trouble Codes [D].

10.

Read the pending DTCs.


HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.



WIRING DIAGRAM

A360380E02
0.708,4.563 1.781,4.76 1.073,0.198 10 false Battery 2.792,2.552 5.396,2.75 2.604,0.198 10 false No. 1 Integration Relay 1.281,4.448 2.458,4.719 1.177,0.271 10 false Starter Assembly 0.552,3.042 1.625,3.24 1.073,0.198 10 false FL MAIN 1,3.656 1.458,3.854 0.458,0.198 10 false C53 1.094,3.448 1.281,3.625 0.188,0.177 10 false 1 1.719,3.427 2.177,3.625 0.458,0.198 10 false C36 1.698,3.229 1.854,3.427 0.156,0.198 10 false 1 3.333,1.875 3.948,2.073 0.615,0.198 10 false ST NO. 2 0.583,0.802 1.042,1 0.458,0.198 10 false E28 0.865,0.802 1.958,1.385 1.094,0.583 10 false Ignition or Starter Switch Assembly 1.313,1.771 1.771,1.969 0.458,0.198 10 false AM2 0.542,1.208 1,1.406 0.458,0.198 10 false AM2 0.938,0.354 1.396,0.552 0.458,0.198 10 false AM2 0.76,0.344 0.917,0.542 0.156,0.198 10 false 5 1.594,0.365 1.906,0.563 0.313,0.198 10 false ST 1.885,0.365 2.042,0.563 0.156,0.198 10 false 4 2.677,1.604 2.99,1.802 0.313,0.198 10 false 1E 2.74,1.427 2.896,1.625 0.156,0.198 10 false 6 2.698,1.219 3.01,1.417 0.313,0.198 10 false 1F 2.698,1.031 3.01,1.229 0.313,0.198 10 false 16 4.281,2.354 4.594,2.552 0.313,0.198 10 false 1J 4.229,2.167 4.385,2.365 0.156,0.198 10 false 4 4.438,1.229 4.75,1.427 0.313,0.198 10 false 1F 4.427,1.042 4.74,1.24 0.313,0.198 10 false 14 4.438,0.667 4.75,0.865 0.313,0.198 10 false 1F 4.438,0.5 4.75,0.698 0.313,0.198 10 false 15 6.042,4.396 6.5,4.594 0.458,0.198 10 false ECM 5.323,0.667 5.781,0.865 0.458,0.198 10 false A24 5.365,0.479 5.677,0.677 0.313,0.198 10 false 60 5.323,1.219 5.781,1.417 0.458,0.198 10 false A24 5.375,1.052 5.688,1.25 0.313,0.198 10 false 46 5.323,3.375 5.781,3.573 0.458,0.198 10 false C50 5.323,3.188 5.781,3.385 0.458,0.198 10 false 105 5.646,0.667 6.26,0.865 0.615,0.198 10 false STSW 5.635,1.219 6.25,1.417 0.615,0.198 10 false STR- 5.656,3.375 5.969,3.573 0.313,0.198 10 false E1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STA SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Data List / STA SW.


e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.43 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Result:
Condition STA SW Proceed to
Driving at 20 km/h (12.43 mph) or more OFF A
ON B



A

B

2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-60(STSW) or 1F-15 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 1 INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT NO. 1 INTEGRATION RELAY
a.

Inspect the No. 1 integration relay (ST NO. 2 relay).

Click hereEngine / Hybrid System>1NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)

NG

4.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E28-4(ST) - 1F-16 Always Below 1 Ω
E28-4(ST) or 1F-16 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

5.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1NR-VE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0617)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / EFI / Trouble Codes.


h.

Read the DTCs.


Result:
Result Proceed to
DTC P0617 is output A
DTCs are not output B



A

B