Home › Engine / Hybrid System › 1NR-VE ENGINE CONTROL › SFI SYSTEM › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042271 1NR-VE ENGINE CONTROL _0196149 SFI SYSTEM C

1NR-VE ENGINE CONTROL  SFI SYSTEM  P0132  Oxygen Sensor (Front) System Range High  


DESCRIPTION

HINT:

Oxygen sensor refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a oxygen sensor is used. The oxygen sensor is located in front of the TWC, and detects the oxygen concentration in the exhaust gas.

Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low). When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The oxygen sensor indicates to the ECM that the pre-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The oxygen sensor indicates to the ECM that the pre-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The oxygen sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the oxygen sensor to determine whether the air-fuel ratio in front of the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A115539E03
2.981,1.232 3.287,0.841 false 2.687,1.79 3.304,1.79 false 2.596,2.418 3.255,2.383 false 2.677,2.697 3.258,2.832 false 1.093,2.916 1.331,2.916 false 1.452,0.775 2.460,0.977 1.009,0.202 10 Atmospheric Air 3.308,0.74 4.048,0.942 0.739,0.202 10 Housing 3.32,1.186 4.848,1.388 1.528,0.202 10 Platinum Electrode 3.955,0.89 4.920,1.092 0.964,0.202 10 Output Voltage 5.006,0.932 6.392,1.134 1.386,0.202 10 Ideal Air-fuel Mixture 2.007,3.13 2.907,3.332 0.899,0.202 10 Exhaust Gas 3.34,1.698 4.802,2.066 1.461,0.368 10 Solid Electrolyte (Zirconia Element) 3.294,2.757 4.497,2.959 1.203,0.202 10 Coating (Ceramic) 3.32,2.284 3.803,2.486 0.483,0.202 10 Heater 1.367,2.82 1.805,3.032 0.438,0.211 10 Cover 4.787,2.849 7.090,3.050 2.304,0.202 10 Richer - Air-fuel Ratio - Leaner 2.668,1.455 2.667,1.53 false 2.725,1.641 3.306,1.271 3.306,1.271 2.667,1.494 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0132 Oxygen Sensor (Front) System Range High Oxygen sensor voltage output exceeds 2.4 V for more than 10 seconds (2 trip detection logic)
·

Short in oxygen sensor circuit

·

Oxygen sensor

·

ECM internal circuit malfunction


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" procedure of the following diagnostic troubleshooting procedure.

A232734E18
6.156,2.427 6.156,2.875 false 5.135,2.438 5.135,2.875 false 4.094,2.427 4.094,2.885 false 0.104,0.125 1.031,0.417 0.927,0.292 10 false Vehicle Speed 0.25,0.958 0.833,1.25 0.583,0.292 10 false 40 km/h 0.51,1.635 0.865,1.917 0.354,0.281 10 false Idling 0.177,1.844 0.854,2.438 0.677,0.594 10 false Ignition Switch ON 1.115,1.938 1.375,2.156 0.26,0.219 10 false [A] 1.625,1.573 1.896,1.781 0.271,0.208 10 false [B] 2.646,0.292 2.917,0.531 0.271,0.24 10 false [C] 4.542,1.573 4.844,1.833 0.302,0.26 10 false [E] 4.021,0.688 4.302,0.979 0.281,0.292 10 false [D] 5.563,1.552 5.865,1.771 0.302,0.219 10 false [E] 6.615,1.552 6.844,1.802 0.229,0.25 10 false [F] 1.323,2.531 2.094,2.854 0.771,0.323 10 false Warming up 2.25,2.542 3.469,2.833 1.219,0.292 10 false 20 minutes or more 4.313,2.521 5.052,3.146 0.74,0.625 10 false 30 seconds or more 5.302,2.5 6.042,3.156 0.74,0.656 10 false 30 seconds or more 5.802,2.896 6.563,3.5 0.76,0.604 10 false 20 seconds or more 6.313,2.51 7.052,3.167 0.74,0.656 10 false 40 seconds or more 5.052,0.698 5.323,0.938 0.271,0.24 10 false [D] 6.083,0.719 6.385,0.938 0.302,0.219 10 false [D] 4.792,2.896 5.552,3.5 0.76,0.604 10 false 20 seconds or more 3.771,2.896 4.531,3.5 0.76,0.604 10 false 20 seconds or more 0.25,0.583 0.833,0.875 0.583,0.292 10 false 60 km/h

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on [A].

3.

Clear the DTCs.

4.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) [B].

5.

Drive the vehicle at 60 km/h (37 mph) or more for 20 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

This step is performed to complete ethanol concentration learning.

·

If DTC P0132 is output when any of the following conditions is met, it is necessary to complete ethanol concentration learning to meet preconditions.


·

The battery has been disconnected and reconnected.

·

The DTCs have been cleared.

·

Both fuel tank assemblies (for main and sub tanks) have been filled with fuel.



6.

Drive the vehicle at more than 40 km/h (25 mph) for 20 seconds or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


7.

Allow the engine to idle for 30 seconds or more [E].

8.

Repeat procedure [D] and [E] described above at least 3 times.

9.

Allow the engine to idle for 40 seconds or more [F].

10.

Enter the following menus: Powertrain / EFI / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A360376E06
0.771,0.604 1.083,0.802 0.313,0.198 10 false 1F 0.75,0.417 0.948,0.604 0.198,0.188 10 false 17 2.802,0.604 3.115,0.802 0.313,0.198 10 false 1J 2.833,0.438 2.99,0.635 0.156,0.198 10 false 3 2.802,1.146 3.115,1.344 0.313,0.198 10 false 1F 2.844,0.958 3,1.156 0.156,0.198 10 false 5 1.823,1.469 3.052,1.667 1.229,0.198 10 false EFI-MAIN 1.198,1.802 2.594,2.063 1.396,0.26 10 false No. 1 Integration Relay 0.417,2.563 0.875,2.76 0.458,0.198 10 false EFI 0.438,3.198 1.052,3.458 0.615,0.26 10 false FL MAIN 0.594,3.917 1.156,4.219 0.563,0.302 10 false Battery 3.635,0.5 4.052,0.719 0.417,0.219 10 false HTR+ 3.448,0.5 3.604,0.698 0.156,0.198 10 false 2 4.448,0.5 4.896,0.74 0.448,0.24 10 false HTR- 4.854,0.51 5.01,0.708 0.156,0.198 10 false 1 3.635,1.167 3.792,1.365 0.156,0.198 10 false E 3.458,1.167 3.615,1.365 0.156,0.198 10 false 4 4.656,1.156 4.813,1.354 0.156,0.198 10 false + 4.854,1.146 5.01,1.344 0.156,0.198 10 false 3 3.604,1.719 3.927,1.917 0.323,0.198 10 false C22 3.906,1.719 4.948,2.01 1.042,0.292 10 false Oxygen Sensor 3.177,4.188 3.979,4.448 0.802,0.26 10 false *:Shielded 6.375,3.615 6.833,3.813 0.458,0.198 10 false ECM 5.813,3.042 6.271,3.24 0.458,0.198 10 false A24 5.854,2.865 6.167,3.063 0.313,0.198 10 false 28 6.135,3.052 6.594,3.25 0.458,0.198 10 false MRO 6.125,2.635 6.583,2.833 0.458,0.198 10 false OX- 5.813,2.625 6.271,2.823 0.458,0.198 10 false C50 5.854,2.458 6.167,2.656 0.313,0.198 10 false 51 6.135,1.26 6.448,1.458 0.313,0.198 10 false OX 5.813,1.25 6.271,1.448 0.458,0.198 10 false C50 5.854,1.073 6.167,1.271 0.313,0.198 10 false 30 6.125,0.594 6.531,0.813 0.406,0.219 10 false OXH1 5.813,0.594 6.271,0.792 0.458,0.198 10 false C50 5.896,0.417 6.052,0.615 0.156,0.198 10 false 8 5.354,2.875 5.51,3.073 0.156,0.198 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (OXYGEN SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Enter the following menus: Powertrain / EFI / Data List / O2S B1S1.


c.

Allow the engine to run at 2500 rpm for 3 minutes.


d.

Depress the accelerator pedal quickly until the engine speed reaches 4000 rpm 3 times.


Result:
Result Proceed to
More than 2.4 V A
Less than 1.0 V B



A

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

B

4.READ OUTPUT DTC (P0132)
2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Disconnect the oxygen sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-30 (OX) - C50-8 (OXH1) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT OXYGEN SENSOR (HEATER RESISTANCE)
3.INSPECT OXYGEN SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (ECM - OXYGEN SENSOR)

NG

4.READ OUTPUT DTC (P0132)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and wait 5 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / EFI / Trouble Codes.


i.

Read the DTCs.


Result:
Result Proceed to
DTC P0132 is output A
DTC is not output B



A

B