Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/o Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196163 SFI SYSTEM(w/o Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/o Air Fuel Ratio Sensor)  P0335  Crankshaft Position Sensor "A" Circuit  P0337  Crankshaft Position Sensor "A" Circuit Low Input  P0338  Crankshaft Position Sensor "A" Circuit High Input  P0339  Crank Angle Sensor Signal Flash Open  


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft angle sensor plate and Magneto Resistance Element (MRE) type sensor. The crankshaft angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit Either of the following conditions is met (1 trip detection logic):
·

No crankshaft position sensor signal to the ECM while cranking.

·

No crankshaft position sensor signal to the ECM while engine running.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crankshaft angle sensor plate)

·

ECM


Comes on DTC stored
P0337 Crankshaft Position Sensor "A" Circuit Low Input Output voltage of crankshaft position sensor is less than 0.3 V for 0.43 seconds or more (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored
P0338 Crankshaft Position Sensor "A" Circuit High Input Output voltage of crankshaft position sensor is higher than 4.7 V for 0.43 seconds or more (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored
P0339 Crank Angle Sensor Signal Flash Open Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or more.
(b) Starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft (crankshaft angle sensor plate)

·

ECM


Does not come on DTC stored

A200774E12
2.958,1.177 3.344,1.406 0.385,0.229 10 false GND 0.094,0.063 0.823,0.396 0.729,0.333 10 false 2 V/DIV. 1.219,1.875 2.344,2.115 1.125,0.24 10 false 5 msec./DIV.

Reference: Inspection using an oscilloscope.

The correct waveform is as shown.

ECM Terminal Name Between N and EN
Tester Range 2 V/DIV., 5 ms./DIV.
Condition Idling with warm engine


CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more.

8.

Enter the following menus: Powertrain / EFI / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A282693E13
1.177,1.271 1.271,1.438 0.094,0.167 10 false 3 1.354,1.406 1.833,1.646 0.479,0.24 10 false VCG 1.677,1.135 2.281,1.333 0.604,0.198 10 false GIN 1.615,1.688 2.125,1.906 0.51,0.219 10 false EGIN 2.01,1 2.115,1.167 0.104,0.167 10 false 1 2.01,1.573 2.115,1.74 0.104,0.167 10 false 2 0.302,1.896 0.573,2.063 0.271,0.167 10 false C48 0.302,2.063 3.25,2.229 2.948,0.167 10 false Camshaft Position Sensor (for Intake Camshaft) 1.167,5.135 1.26,5.302 0.094,0.167 10 false 3 1.333,5.26 1.854,5.458 0.521,0.198 10 false VCN 1.781,4.99 2.219,5.167 0.438,0.177 10 false N 1.708,5.573 2.365,5.792 0.656,0.219 10 false EN 2.01,4.865 2.115,5.031 0.104,0.167 10 false 1 2.01,5.438 2.115,5.604 0.104,0.167 10 false 2 0.771,5.76 1.042,5.927 0.271,0.167 10 false C38 0.771,5.927 2.51,6.094 1.74,0.167 10 false Crankshaft Position Sensor 1.177,3.188 1.271,3.354 0.094,0.167 10 false 3 1.354,3.313 1.667,3.479 0.313,0.167 10 false VC 1.646,3.042 2.24,3.208 0.594,0.167 10 false GEX 1.542,3.625 2.094,3.792 0.552,0.167 10 false EGEX 2.01,2.917 2.115,3.083 0.104,0.167 10 false 1 2.01,3.49 2.115,3.656 0.104,0.167 10 false 2 0.302,3.813 0.573,3.979 0.271,0.167 10 false C49 0.302,3.979 3.396,4.146 3.094,0.167 10 false Camshaft Position Sensor (for Exhaust Camshaft) 5.042,0.552 5.5,0.719 0.458,0.167 10 false VCG 4.771,0.438 5.302,0.719 0.531,0.281 10 false 58 5.031,1.125 5.594,1.354 0.563,0.229 10 false GIN 4.792,1.01 5.177,1.313 0.385,0.302 10 false 80 5.042,1.719 5.521,2.042 0.479,0.323 10 false EGIN 4.729,1.594 5.438,1.927 0.708,0.333 10 false 102 5.042,2.469 5.448,2.646 0.406,0.177 10 false VCG 4.771,2.354 5.333,2.677 0.563,0.323 10 false 59 5.042,3.052 5.448,3.229 0.406,0.177 10 false GEX 4.792,2.927 5.229,3.177 0.438,0.25 10 false 81 5.042,3.615 5.479,3.781 0.438,0.167 10 false EGEX 4.729,3.5 5.219,3.76 0.49,0.26 10 false 103 5.042,4.417 5.542,4.604 0.5,0.188 10 false VCN 4.792,4.281 5.323,4.563 0.531,0.281 10 false 57 5.042,5 5.573,5.188 0.531,0.188 10 false N 4.792,4.875 5.26,5.167 0.469,0.292 10 false 79 5.042,5.573 5.313,5.74 0.271,0.167 10 false EN 4.729,5.448 5.26,5.708 0.531,0.26 10 false 101 5.146,6.042 5.417,6.208 0.271,0.167 10 false C50 5.479,6.042 5.844,6.198 0.365,0.156 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

1.

Connect the GTS to the DLC3.

2.

Start the engine.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / EFI / Data List / Engine revolution speed.


The Engine revolution speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the Engine revolution speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE REVOLUTION SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Data List / Engine revolution speed.


e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the Engine revolution speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the Engine revolution speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
a.
A359813C05
0.208,2.073 0.667,2.354 0.458,0.281 2.271,3.083 1.896,2.5 true 0.208,0.198 0.417,0.375 0.208,0.177 10 false *a 0.313,2.146 0.583,2.302 0.271,0.156 10 false C38 2.25,3.146 2.677,3.354 0.427,0.208 10 false VCN
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C38-3 (VCN) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C38-1 (N) - C50-79 (N) Always Below 1 Ω
C38-2 (EN) - C50-101 (EN) Always Below 1 Ω
C38-1 (N) or C50-79 (N) - Body ground Always 10 kΩ or higher
C38-2 (EN) or C50-101 (EN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
B319222C17
2.146,1.563 2.813,1.792 0.667,0.229 10 false *c 0.469,1.781 0.781,1.979 0.313,0.198 10 false *a 2.656,1.781 2.969,1.979 0.313,0.198 10 false *b
*a OK
*b NG
*c Clearance


Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT (CRANKSHAFT ANGLE SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT CRANKSHAFT (CRANKSHAFT ANGLE SENSOR PLATE)
a.

Check the teeth of the crankshaft angle sensor plate.

OK:

Crankshaft angle sensor plate does not have any cranks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE CRANKSHAFT (CRANKSHAFT ANGLE SENSOR PLATE)

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335, P0337, P0338 AND/OR P0339)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335, P0337, P0338 AND/OR P0339)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern.


i.

Enter the following menus: Powertrain / EFI / Trouble Codes.


j.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P0335, P0337, P0338 and/or P0339 are output B



A

END

B

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C38-3 (VCN) - C50-57 (VCN) Always Below 1 Ω
C38-3 (VCN) or C50-57 (VCN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR