The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.
The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2102 | Throttle Actuator Control Motor Circuit Open | Both of the following conditions are met for 2.0 seconds (1 trip detection logic):
(a) The throttle actuator drive duty cycle is 80% or higher. (b) The throttle actuator current is less than 0.5 A. |
·
Open in throttle actuator circuit ·
Throttle actuator ·
ECM |
Comes on | DTC stored |
| P2103 | Throttle Actuator Control Motor Circuit Short | The following conditions is met (1 trip detection logic):
A motor deriver IC detects high current. |
·
Short in throttle actuator circuit ·
Throttle actuator ·
Throttle valve ·
Throttle body with motor assembly ·
ECM |
Comes on | DTC stored |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Start the engine.
With the vehicle stationary, fully depress the accelerator pedal and quickly release it [B].
Check that 16 seconds or more have elapsed from the instant when the accelerator pedal is first depressed.
Enter the following menus: Powertrain / EFI / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle valve opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.
The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle motor open duty ratio / Throttle motor close duty ratio) can be read using the GTS. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Inspect the throttle body with motor assembly.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>THROTTLE BODY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle body with motor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C47-2 (M+) - C50-1 (M+) | Always | Below 1 Ω |
| C47-1 (M-) - C50-2 (M-) | Always | Below 1 Ω |
| C47-2 (M+) or C50-1 (M+) - Body ground and other terminals | Always | 10 kΩ or higher |
| C47-1 (M-) or C50-2 (M-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for foreign matter between the throttle valve and the housing.
No foreign matter between the throttle valve and housing.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if the throttle valve opens and closes smoothly.
Throttle valve opens and closes smoothly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG