Refer to DTC P2120.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/o Air Fuel Ratio Sensor)>P2120
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2121 | Accelerator Pedal Position Sensor Range/Performance | Either of following conditions (a) or (b) met for 0.5 seconds (1 trip detection logic):
(a) Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position) (b) Difference between VPA and VPA2 is greater than or equal to the specified value. |
·
Accelerator pedal sensor assembly ·
ECM |
Comes on | DTC stored |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Wait for 5 seconds after turning the ignition switch to ON.
Operate the accelerator pedal in accordance with the following procedure [B].
Enter the following menus: Powertrain / EFI / Data List / Main accelerator position, and Sub accelerator position.
Slowly depress the accelerator pedal until Main accelerator position is approximately 30% and Sub accelerator position is approximately 46%, then slowly release the accelerator pedal.
Enter the following menus: Powertrain / EFI / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to fail-safe mode. In fail-safe mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.
If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to normal.
Refer to DTC P2120.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/o Air Fuel Ratio Sensor)>P2120
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
If any DTCs other than P2121 are output, troubleshoot those DTCs first.
| Result | Proceed to |
|---|---|
| DTC P2121 is output | A |
| DTC P2121 and other DTCs are output | B |
A
B
| *a | Fully Depressed |
| *b | Fully Released |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / EFI / Data List / Main accelerator sensor voltage and Sub accelerator sensor voltage.
Read the values displayed on the GTS.
| Accelerator Pedal Operation | Main accelerator sensor voltage | Sub accelerator sensor voltage |
|---|---|---|
| Fully Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Fully Depressed | 2.6 to 4.5 V | 3.4 to 4.75 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2121 is output | A |
| DTC is not output | B |
A
B