When the ignition switch is turned to ON, battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MRO terminal of the ECM causes current to flow to the coil of the No. 1 integration relay (EFI-MAIN relay), closing the contacts of the EFI-MAIN relay and supplying power to terminals +B1 and +B2 of the ECM.
Inspect the fuses for circuits related to this system before performing the following procedure.
| *a | Component with harness connected
(No. 1 Integration Relay) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1F-10 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 integration relay (EFI-MAIN relay) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1F-10 - A24-1 (+B1) | Always | Below 1 Ω |
| 1F-10 - A24-2 (+B2) | Always | Below 1 Ω |
| 1F-10 or A24-1 (+B1) - Body ground | Always | 10 kΩ or higher |
| 1F-10 or A24-2 (+B2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C50-4 (E01) - Body ground | Always | Below 1 Ω |
| C50-5 (E02) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the No. 1 integration relay (EFI-MAIN relay) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-28 (MRO) - 1F-5 | Always | Below 1 Ω |
| A24-28 (MRO) or 1F-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (EFI-MAIN relay).
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Integration Relay (EFI-MAIN Relay)) |
Disconnect the No. 1 integration relay (EFI-MAIN relay) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1F-17 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the No. 1 integration relay (IG2 relay) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-14 (IGSW) - 1D-5 | Always | Below 1 Ω |
| A24-14 (IGSW) or 1D-5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (IG2 relay).
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 integration relay (IG2 relay) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1D-1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Integration Relay (IG2 Relay)) |
Disconnect the No. 1 integration relay (IG2 relay) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1E-5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 1 integration relay (IG2 relay) connector.
Disconnect the ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1F-18 - E28-2 (IG1) | Always | Below 1 Ω |
| 1F-18 or E28-2 (IG1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>2NR-VE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG