Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/o Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196163 SFI SYSTEM(w/o Air Fuel Ratio Sensor) J

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/o Air Fuel Ratio Sensor)  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Light (MIL) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is turned to ON, the MIL should be illuminated and should then turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A266546E06
5.292,2.833 5.948,3.24 0.656,0.406 10 false ECM 4.948,1.229 5.615,1.625 0.667,0.396 10 false HCAN 1.469,1.229 2.333,1.708 0.865,0.479 10 false CANH 4.958,1.969 5.688,2.323 0.729,0.354 10 false LCAN 1.49,1.979 2.156,2.292 0.667,0.313 10 false CANL 0.5,2.844 2.573,3.271 2.073,0.427 10 false Combination Meter Assembly 0.76,3.438 2.865,3.802 2.104,0.365 10 false : CAN Communication Line 0.5,2.667 1.167,2.979 0.667,0.313 10 false E34 5.292,2.667 5.958,2.979 0.667,0.313 10 false A24 1.969,1.052 2.24,1.323 0.271,0.271 10 false 9 1.979,1.792 2.25,2.063 0.271,0.271 10 false 8 4.688,1.052 4.958,1.323 0.271,0.271 10 false 25 4.688,1.792 4.958,2.063 0.271,0.271 10 false 26

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
Result Condition Proceed to
MIL ON → MIL OFF Ignition switch ON → Engine is started A
Other than the above - B



A

B

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

Checking the Data List for "EFI" is possible.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

4.PERFORM ACTIVE TEST USING GTS (CHECK MIL)

B

REPAIR CIRCUIT INDICATED BY OUTPUT

4.PERFORM ACTIVE TEST USING GTS (CHECK MIL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Meter / Active Test / Indicator 18 / Engine warning.


e.

Check the status of the MIL while performing the Active Test.


Result:
Result Proceed to
Changes A
Does not change B



A

B

REPLACE COMBINATION METER ASSEMBLY