Home › Engine / Hybrid System › 2NR-VE ENGINE MECHANICAL › CAMSHAFT › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042274 2NR-VE ENGINE MECHANICAL _0196189 CAMSHAFT A

2NR-VE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 23250 3.REMOVE FUEL INJECTOR ASSEMBLY

Hide 16267 4.DISCONNECT NO. 3 WATER BY-PASS HOSE

a.
A360076

Loosen the clamp and disconnect the No. 3 water by-pass hose.


Hide 16281 5.DISCONNECT NO. 4 WATER BY-PASS HOSE

Hide 87245X 6.DISCONNECT HEATER WATER HOSE (w/ Heater)

Hide 87246X 7.DISCONNECT NO. 2 HEATER WATER HOSE (w/ Heater)

Hide 16591A 8.DISCONNECT RADIATOR PIPE RADIATOR HOSE

a.
A360075

Loosen the hose clamp and disconnect the radiator pipe radiator hose.


Hide 16571C 9.REMOVE NO. 1 RADIATOR HOSE

Hide 16507 10.REMOVE RADIATOR PIPE SUB-ASSEMBLY

a.
A360023

w/ Air Fuel Ratio Sensor:

i.

Disconnect the air fuel ratio sensor connector.



b.

w/o Air Fuel Ratio Sensor:

i.

Disconnect the oxygen sensor connector.



c.

Disengage the 2 harness clamps and disconnect the wire harness from the radiator pipe sub-assembly.


d.
A364898

Remove the 2 bolts and radiator pipe sub-assembly.


Hide 11302 11.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13540 12.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.

Set the camshaft timing gear assembly, camshaft timing exhaust gear assembly and crankshaft in the positions (20° ATDC) shown in the illustration.

A360071C01
1.146,3.688 1.771,3.333 true 3.177,1.021 3.99,1.094 true 3.948,1.24 3.188,1.021 3.188,1.021 3.969,1.021 true 5.344,1.042 6.156,1.177 6.156,1.177 5.271,1.146 true 0.99,3.656 1.302,3.854 0.313,0.198 10 false *a 2.219,3.406 2.531,3.604 0.313,0.198 10 false *b 1.938,3.656 2.25,3.854 0.313,0.198 10 false 20° 2.198,2.948 2.51,3.146 0.313,0.198 10 false 23° 2.948,0.917 3.26,1.115 0.313,0.198 10 false *a 6.229,1.073 6.542,1.271 0.313,0.198 10 false *a 4.104,0.708 4.417,0.906 0.313,0.198 10 false 10° 5.396,0.719 5.708,0.917 0.313,0.198 10 false 10°
*a Timing Mark *b TDC


NOTICE:

Never turn the crankshaft counterclockwise (when viewed from the front of the engine).



b.
A197602C08
1.563,1.031 0.563,1.031 true 2.188,1.24 2.844,0.708 true 0.396,0.958 0.667,1.188 0.271,0.229 10 false *a 2.896,0.646 3.208,0.896 0.313,0.25 10 false *b
*a Stopper Plate
*b Plunger
V100136

Push


Push down the stopper plate to release the lock and push in the plunger.


c.
A197601C07
2.521,0.167 1.844,0.802 true 2.563,0.063 2.771,0.229 0.208,0.167 10 *a
*a Stopper Plate


Pull up the stopper plate with the plunger pushed to the end to lock the plunger.


d.
A197603C15
0.833,1.635 1.073,0.99 true 0.75,1.656 0.979,1.906 0.229,0.25 10 false *a
*a Pin


Insert a pin of 3 mm (0.118 in.) diameter into the hole in the stopper plate.


e.
A197604

Remove the 2 nuts and No. 1 chain tensioner assembly.


Hide 13562 13.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A197605

Remove the 2 bolts and No. 2 chain vibration damper.


Hide 13591 14.REMOVE TIMING CHAIN TENSION ARM

a.
A361362

Remove the timing chain tension arm.


Hide 13506 15.REMOVE CHAIN SUB-ASSEMBLY

a.

Remove the chain sub-assembly.


Hide 13566B 16.REMOVE TIMING CHAIN GUIDE

a.
A361363

Remove the 2 bolts and timing chain guide.


Hide 13050 17.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Check the lock of the camshaft timing gear assembly.


b.
A198701C13
1.615,0.115 1.167,0.396 true 0.646,2.698 1.063,1.646 true 1.708,0.75 0.844,0.521 true 1.646,0.042 1.844,0.24 0.198,0.198 10 *a 0.542,2.719 0.74,2.917 0.198,0.198 10 *c 1.75,0.698 1.948,0.896 0.198,0.198 10 *b
*a Adhesive Tape Sealing Area
*b Prick a Hole
*c Adhesive Tape


Clean the VVT oil hole on the intake side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



c.

Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure A)


d.
A198702

Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.




e.

Forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

HINT:

Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance by hand.



f.
A200382

Turn the camshaft timing gear assembly within its movable range (26.5 to 28.5°) 2 or 3 times without turning it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.


g.

Remove the adhesive tape from the camshaft bearing cap.


Hide 13070A 18.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Check the lock of the camshaft timing exhaust gear assembly.


b.
A198700C08
2.635,2.688 1.677,1.938 true 1.583,0.208 2.219,0.438 true 1.552,0.781 2.552,0.552 true 2.688,2.646 2.854,2.802 0.167,0.156 10 *c 1.385,0.125 1.552,0.281 0.167,0.156 10 *a 1.385,0.719 1.552,0.875 0.167,0.156 10 *b
*a Adhesive Tape Sealing Area
*b Prick a Hole
*c Adhesive Tape


Clean the VVT oil hole on the exhaust side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



c.

Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure B)


d.
A198703

Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the hole pricked in procedure B to release the lock pin.

NOTICE:
·

If air leaks out, reattach adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.




e.

Using a screwdriver with its tip wrapped with tape, forcibly turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).

NOTICE:
·

Be sure to keep the camshaft timing exhaust gear assembly in the retard direction using a screwdriver. If the camshaft timing exhaust gear assembly is released, it will return to the most advanced position automatically due to force from the spring.

·

Do not damage the camshaft timing exhaust gear assembly.




f.
A198704

Using a screwdriver with its tip wrapped with tape, turn the camshaft timing exhaust gear assembly within its movable range (19 to 21°) 2 or 3 times without turning it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.


g.

Remove the adhesive tape from the camshaft bearing cap.


Hide 13070A 19.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A360072C01
0.552,1.51 0.219,1.656 0.219,1.656 0.719,1.583 true 0.719,1.938 0.458,2.042 0.458,2.042 0.813,1.969 true 0.063,1.573 0.375,1.771 0.313,0.198 10 false *a 0.302,1.969 0.615,2.167 0.313,0.198 10 false *a 2.031,0.313 2.344,0.51 0.313,0.198 10 false *b
*a Do not Remove
*b Hold


Remove the bolt while holding the hexagonal portion of the No. 2 camshaft, then remove the camshaft timing exhaust gear assembly.

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing exhaust gear assembly horizontal while removing it from the No. 2 camshaft.




Hide 13050 20.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A360073C01
0.313,1.073 0.177,1.125 0.177,1.125 0.333,1.365 true 0.458,1.302 0.927,1.677 0.927,1.677 0.5,1.604 true 0.01,1 0.323,1.198 0.313,0.198 10 false *a 1.573,0.146 1.885,0.344 0.313,0.198 10 false *b 0.979,1.677 1.292,1.875 0.313,0.198 10 true *a
*a Do not Remove
*b Hold


Remove the bolt while holding the hexagonal portion of the camshaft, then remove the camshaft timing gear assembly.

NOTICE:
·

Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.

·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.




Hide 21.REMOVE CAMSHAFT BEARING CAP

a.
A361346N01
2.958,1.01 3.198,1.229 0.24,0.219 10 true 1 0.26,0.865 0.5,1.083 0.24,0.219 10 false 2 2.448,0.979 2.688,1.198 0.24,0.219 10 true 3 1.427,0.938 1.667,1.156 0.24,0.219 10 true 4 1.917,0.927 2.156,1.146 0.24,0.219 10 true 5

Uniformly loosen and remove the 5 bolts in the order shown in the illustration.


b.
A361347C01
0.385,0.271 0.573,0.438 true 0.865,2.031 1.104,1.656 true 1.781,1.667 1.99,1.938 1.99,1.938 2.167,1.677 true 2.833,0.469 3.01,0.229 true 0.135,0.417 0.292,0.615 0.156,0.198 10 true 1 0.167,1.573 0.313,1.792 0.146,0.219 10 true 3 2.688,0.031 2.906,0.208 0.219,0.177 10 true 4 0.188,0.885 0.344,1.083 0.156,0.198 10 true 5 2.708,1.958 2.854,2.177 0.146,0.219 10 true 2 2.896,1.177 3.083,1.365 0.188,0.188 10 true 6 1.167,0.021 1.385,0.198 0.219,0.177 10 true 7 2.198,1.938 2.344,2.156 0.146,0.219 10 true 8 1.156,1.958 1.302,2.177 0.146,0.219 10 true 9 2.135,0.021 2.354,0.198 0.219,0.177 10 true 10 1.344,1.167 1.563,1.344 0.219,0.177 10 true 11 2.365,1.177 2.583,1.354 0.219,0.177 10 true 12 1.646,1.948 1.865,2.125 0.219,0.177 10 true 13 1.625,0.042 1.844,0.219 0.219,0.177 10 true 14 1.844,1.188 2.063,1.365 0.219,0.177 10 true 15 0.208,0.135 0.521,0.333 0.313,0.198 10 false *1 0.688,1.979 1,2.177 0.313,0.198 10 false *2 1.917,1.979 2.229,2.177 0.313,0.198 10 false *3 3.021,0.094 3.333,0.292 0.313,0.198 10 false *4
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap
*4 No. 4 Camshaft Bearing Cap


Uniformly loosen and remove the 15 bolts in the order shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



c.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap.

HINT:

Arrange the removed parts in the correct order.



Hide 13512 22.REMOVE NO. 2 CAMSHAFT

a.
A361349

Remove the No. 2 camshaft from the camshaft housing sub-assembly.


Hide 13511 23.REMOVE CAMSHAFT

a.
A361350

Remove the camshaft from the camshaft housing sub-assembly.


Hide 13801 24.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 25.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11103 26.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A361348

Remove the 3 bolts.


b.
A361351C01
0.615,0.656 0.469,0.417 true 1.969,3.99 2.115,3.833 true 2.875,3.229 2.635,3.031 true 0.323,0.271 0.635,0.427 0.313,0.156 10 false *a 2.083,3.688 2.323,3.865 0.24,0.177 10 true *a 2.906,3.229 3.146,3.406 0.24,0.177 10 true *a
*a Protective Tape


Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 13801 27.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 28.INSPECT VALVE LASH ADJUSTER ASSEMBLY