Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) › from 2015.08
RM19Y0E _56 Audio / Visual / Telematics _003000 AUDIO / VIDEO _0015166 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the stereo component tuner assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E234125E04
5.344,3.969 6.969,4.802 1.625,0.833 10 false No. 1 Stereo Jack Adapter Assembly 0.542,3.927 2.146,4.813 1.604,0.885 10 false Stereo Component Tuner Assembly 5.698,1.479 6.333,1.844 0.635,0.365 10 false UDO- 5.698,2.083 6.344,2.448 0.646,0.365 10 false UDO+ 5.698,2.667 6.313,2.938 0.615,0.271 10 false UJSG 5.479,1.396 5.875,1.719 0.396,0.323 10 false 2 5.698,0.885 6.406,1.24 0.708,0.354 10 false UPI 1.302,1.479 1.896,1.781 0.594,0.302 10 false UDI- 1.271,2.083 1.906,2.417 0.635,0.333 10 false UDI+ 1.188,2.677 1.958,3.042 0.771,0.365 10 false UESG 1.281,0.906 1.917,1.229 0.635,0.323 10 false UPO 5.479,0.813 5.854,1.115 0.375,0.302 10 false 1 5.479,2 5.844,2.333 0.365,0.333 10 false 3 5.479,2.594 5.938,2.958 0.458,0.365 10 false 4 0.552,3.76 1.125,4.083 0.573,0.323 10 false E92 5.344,3.802 5.833,4.104 0.49,0.302 10 false E91 1.74,1.406 2.135,1.74 0.396,0.333 10 false 2 1.74,0.813 2.094,1.104 0.354,0.292 10 false 1 1.74,1.99 2.146,2.323 0.406,0.333 10 false 3 1.74,2.583 2.208,2.969 0.469,0.385 10 false 4

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to before play begins.

·

When using a USB device, files that are copy protected or encrypted cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

1.

Add numbers in front of the file names.

2.

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION


Result:
Result Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B




A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

B

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT TUNER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the E92 stereo component tuner assembly connector.


b.

Disconnect the E91 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
E92-1 (UPO) - E91-1 (UPI) Always Below 1 Ω
E92-2 (UDI-) - E91-2 (UDO-) Always Below 1 Ω
E92-3 (UDI+) - E91-3 (UDO+) Always Below 1 Ω
E92-4 (UESG) - E91-4 (UJSG) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
E92-1 (UPO) or E91-1 (UPI) - Body ground Always 10 kΩ or higher
E92-2 (UDI-) or E91-2 (UDO-) - Body ground Always 10 kΩ or higher
E92-3 (UDI+) or E91-3 (UDO+) - Body ground Always 10 kΩ or higher
E92-4 (UESG) or E91-4 (UJSG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

3.INSPECT STEREO COMPONENT TUNER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT TUNER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Disconnect the E91 No. 1 stereo jack adapter assembly connector.


b.
E234124C08
1.5,0.302 1.948,0.583 0.448,0.281 1.396,1.156 1.135,0.719 1.135,0.719 1.01,0.719 true 2.063,1.146 2.26,0.708 2.26,0.708 2.375,0.708 true 0.167,0.104 0.542,0.438 0.375,0.333 10 false *a 1.594,0.365 2.031,0.667 0.438,0.302 10 false E91 0.688,0.635 1.271,1.094 0.583,0.458 10 false UPI 2.448,0.615 3.073,1.052 0.625,0.438 10 false UJSG
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Reconnect the E92 stereo component tuner assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E91-1 (UPI) - E91-4 (UJSG) Ignition switch ACC 5 V


Result:
Proceed to
OK
NG




OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE STEREO COMPONENT TUNER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Make sure that back up music data is available before performing this operation.


OK:

Malfunction disappears.


Result:
Proceed to
OK
NG




OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)>SYSTEM DESCRIPTION



Result:
Proceed to
NEXT




NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if USB device or "iPod" is recognized by the stereo component tuner assembly, or if information such as track, artist and album names are displayed on screen.

OK:

Malfunction disappears.


Result:
Proceed to
OK
NG




OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG