Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003012 SEAT BELT _0015223 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

When the ignition switch is turned to ON, the main body ECU (fuse block assembly) determines whether the front passenger side seat is occupied or not, and whether the front seat inner belt assembly LH*1 or RH*2 is fastened or not, and transmits a signal to the combination meter assembly through the CAN. If the front seat inner belt assembly LH*1 or RH*2 is unfastened even when the front passenger side seat is occupied, the combination meter assembly will cause the front passenger side seat belt warning light in the hazard warning signal switch assembly to blink. When the front seat inner belt assembly LH*1 or RH*2 is fastened, the front passenger side seat belt warning light goes off.

*1: for RHD

*2: for LHD


WIRING DIAGRAM

E327365E01
0.479,5.365 2.542,5.719 2.063,0.354 10 false : CAN Communication Line 3.083,4.563 6.75,5 3.667,0.438 10 false Belt Warning Occupant Detection Sensor 0.167,4.583 3.833,5.021 3.667,0.438 10 false Main Body ECU (Fuse Block Assembly) 4.771,3.823 6.104,4.49 1.333,0.667 10 false Front Seat Inner Belt Assembly LH*1/RH*2 4.667,2.333 6.167,2.833 1.5,0.5 10 false Telltale Light Assembly 2.417,2.5 4.333,3 1.917,0.5 10 false Combination Meter Assembly 2.417,2.365 4.333,2.865 1.917,0.5 10 false E34 5.042,0.594 6.177,1.094 1.135,0.5 10 false ECU IG2 1.656,1.51 3.573,2.01 1.917,0.5 10 false 3G 1.656,2.021 3.573,2.521 1.917,0.5 10 false 3G 1.656,3.438 3.573,3.938 1.917,0.5 10 false 3K 2.896,3.438 4.813,3.938 1.917,0.5 10 false J23 2.521,3.438 4.438,3.938 1.917,0.5 10 false J24 6.24,3.438 7.146,3.938 0.906,0.5 10 false J23 5.865,3.438 6.688,3.938 0.823,0.5 10 false J24 1.698,3.229 3.615,3.729 1.917,0.5 10 false 3 2.896,3.24 4.813,3.74 1.917,0.5 10 false 1*2 5.885,3.25 7.125,3.75 1.24,0.5 10 false 2*1 6.25,3.25 7.156,3.75 0.906,0.5 10 false 2*2 4.313,3.802 5.552,4.302 1.24,0.5 10 false A 3.323,3.802 4.563,4.302 1.24,0.5 10 false A 1.688,1.792 3.604,2.292 1.917,0.5 10 false 16 1.667,1.271 3.583,1.771 1.917,0.5 10 false 17 2.417,1.25 4.333,1.75 1.917,0.5 10 false 9 2.417,1.833 4.333,2.333 1.917,0.5 10 false 8 4.667,2.135 6.583,2.635 1.917,0.5 10 false E79 4.604,1.646 6.521,2.146 1.917,0.5 10 false 5 5.781,1.656 7.104,2.156 1.323,0.5 10 false 1 4.104,1.646 6.021,2.146 1.917,0.5 10 false 19 3.531,1.802 5.448,2.302 1.917,0.5 10 false BTWG 2.667,1.51 4.583,2.01 1.917,0.5 10 false CANH 2.667,2 4.583,2.5 1.917,0.5 10 false CANL 2.531,3.229 4.448,3.729 1.917,0.5 10 false 1*1 0.917,1.5 2.833,2 1.917,0.5 10 false CANH 0.917,2 2.833,2.5 1.917,0.5 10 false CANL 0.927,3.448 2.844,3.948 1.917,0.5 10 false PBKL 2.677,5.417 4.177,5.823 1.5,0.406 10 false *1: for RHD 3.677,5.417 5.177,5.823 1.5,0.406 10 false *2: for LHD 3.25,3.417 5.167,3.917 1.917,0.5 10 false + 5.667,3.448 7.156,4.115 1.49,0.667 10 false - 3.594,3.813 4.917,4.313 1.323,0.5 10 false 1 4.594,3.813 5.917,4.313 1.323,0.5 10 false 2 2.083,0.417 3.917,0.917 1.833,0.5 10 false from No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (PASSENGER BUCKLE SW)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical > Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Passenger buckle SW Front passenger side seat belt buckle switch signal ON or OFF ON: Front passenger side seat belt fastened
OFF: Front passenger side seat belt not fastened
The front passenger side seat is occupied

OK:

The GTS or Techstream display changes correctly in response to the front passenger side seat belt condition.


Result:
Proceed to
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - TELLTALE LIGHT ASSEMBLY)

NG

5.INSPECT BELT WARNING OCCUPANT DETECTION SENSOR
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - TELLTALE LIGHT ASSEMBLY)
a.

Disconnect the E79 telltale light assembly connector.


b.
E325404C02
1.5,0.167 2,0.417 0.5,0.25 1.625,0.219 2.083,0.417 0.458,0.198 10 false E79 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Telltale Light Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E79-1 - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG




OK

3.INSPECT TELLTALE LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT TELLTALE LIGHT ASSEMBLY
a.

Remove the telltale light assembly.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>REMOVAL


b.

Inspect the telltale light assembly.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>INSPECTION

Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE TELLTALE LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the E79 telltale light assembly connector.


b.

Disconnect the E34 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E79-5 - E34-19 (BTWG) Always Below 1 Ω
E79-5 or E34-19 (BTWG) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BELT WARNING OCCUPANT DETECTION SENSOR
a.

Remove the belt warning occupant detection sensor.

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL


b.

Inspect the belt warning occupant detection sensor.

Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION

Result:
Proceed to
OK
NG




OK

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY

NG

REPLACE BELT WARNING OCCUPANT DETECTION SENSOR

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY
a.

Remove the front seat inner belt assembly LH*1 or RH*2.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly LH*1 or RH*2.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION

*1: for RHD

*2: for LHD



Result:
Result Proceed to
OK A
NG (for RHD) B
NG (for LHD) C



A

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BODY GROUND)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the 3K main body ECU (fuse block assembly) connector.


b.

Disconnect the J24*1 or J23*2 front seat inner belt assembly LH*1 or RH*2 connector.

*1: for RHD

*2: for LHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
3K-3 - J24-1 (+) Always Below 1 Ω
3K-3 or J24-1 (+) - Body ground Always 10 kΩ or higher
J24-2 (-) - Body ground Always Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
3K-3 - J23-1 (+) Always Below 1 Ω
3K-3 or J23-1 (+) - Body ground Always 10 kΩ or higher
J23-2 (-) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR