Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003007 LIGHTING (INT) _0015198 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  IG Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ON or off condition, and sends it to the main body ECU (fuse block assembly).

WIRING DIAGRAM

E326836E01
1.25,0.521 3.333,1.438 2.083,0.917 10 false from No. 1 Integration Relay 4.5,2.833 7.156,3.802 2.656,0.969 10 false Main Body ECU (Fuse Block Assembly) 4.49,2.281 7.146,3.25 2.656,0.969 10 false 3G 4.469,1.729 7.125,2.698 2.656,0.969 10 false 3G 4.479,1.135 7.135,2.104 2.656,0.969 10 false 3G 4.49,0.531 7.146,1.5 2.656,0.969 10 false 3C 6.083,0.583 7.021,1.667 0.938,1.083 10 false IG1 5.354,0.688 6.292,1.771 0.938,1.083 10 false ECU-IG1 4.51,0.323 5.448,1.406 0.938,1.083 10 false 6 4.5,0.917 5.438,2 0.938,1.083 10 false 12 4.5,2.083 5.438,3.167 0.938,1.083 10 false 11 4.5,1.51 5.438,2.594 0.938,1.083 10 false 1 6.083,1.146 7.021,2.229 0.938,1.083 10 false E01 6.083,1.729 7.021,2.813 0.938,1.083 10 false E11 6.083,2.292 7.021,3.375 0.938,1.083 10 false E12

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (IG SW(IG1)(MAIN))
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical / Body / Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG SW(IG1)(Main) Ignition switch ON signal ON or OFF ON: Ignition switch ON
OFF: Ignition switch off
-

OK:

Normal conditions listed above are displayed.


Result:
Proceed to
OK
NG




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BATTERY AND BODY GROUND)
a.
C334162C01
1.333,0.25 2,0.583 0.667,0.333 1.583,0.333 1.896,0.531 0.313,0.198 10 false 3C 0.198,0.115 0.51,0.271 0.313,0.156 10 false *a
*a Component with harness connected
(to Main Body ECU (Fuse Block Assembly) connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3C-6 - Body ground Ignition switch ON 11 to 14 V



b.

Disconnect the 3G main body ECU (fuse block assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3G-1 - Body ground Always Below 1 Ω
3G-11 - Body ground Always Below 1 Ω
3G-12 - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG C




A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR