Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003007 LIGHTING (INT) _0015198 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (fuse block assembly).

WIRING DIAGRAM

E324027E01
4.083,1.833 7.156,2.458 3.073,0.625 10 false Main Body ECU (Fuse Block Assembly) 3.49,1.135 6.563,1.76 3.073,0.625 10 false 3I 3.469,0.646 6.542,1.271 3.073,0.625 10 false 3A 0.427,1.125 2.333,1.667 1.906,0.542 10 false from Ignition or Starter Switch Assembly 1.5,0.625 2.667,1 1.167,0.375 10 false from Battery 4.521,1.458 5.688,1.833 1.167,0.375 10 false ACC 5.375,0.792 6.542,1.167 1.167,0.375 10 false ACC 6.083,0.646 7.156,0.979 1.073,0.333 10 false ACC 6.083,1.135 7.156,1.469 1.073,0.333 10 false E01 3.521,0.938 4.521,1.271 1,0.333 10 false 5 3.5,0.438 4.5,0.771 1,0.333 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (ACC SW(MAIN))
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Data List.


e.

Read the Data List according to the display on the GTS or Techstream.

Body Electrical / Body / Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ACC SW(Main) Ignition switch ACC signal ON or OFF ON: Ignition switch ACC
OFF: Ignition switch off
-

OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BATTERY)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (FUSE BLOCK ASSEMBLY) - BATTERY)
a.
B418228C01
1.417,2.583 2,2.833 0.583,0.25 1.417,0.5 2,0.75 0.583,0.25 1.604,0.552 1.917,0.75 0.313,0.198 10 false 3A 1.667,2.635 1.979,2.833 0.313,0.198 10 false 3l 0.25,0.365 0.563,0.521 0.313,0.156 10 false *a
*a Component with harness connected
(to Main Body ECU (Fuse Block Assembly) connector)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3A-1 - Body ground Always 11 to 14 V
3l-5 - Body ground Ignition switch ACC 11 to 14 V



Result:
Result Proceed to
OK (for RHD) A
OK (for LHD) B
NG C



A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR