Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2015.08
RM19Y0E _59 Vehicle Exterior _003020 LIGHTING (EXT) _0015281 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (fuse block assembly) controls the front fog lights.

WIRING DIAGRAM

E323367E02
4.823,2.208 5.354,2.552 0.531,0.344 10 false FOG 4.698,1.292 5.552,1.698 0.854,0.406 10 false FOG LH 4.688,0.844 5.542,1.25 0.854,0.406 10 false FOG RH 6.063,1.917 6.917,2.323 0.854,0.406 10 false FOGO 6.063,2.5 6.917,2.906 0.854,0.406 10 false E01 3.875,0.677 4.729,1.083 0.854,0.406 10 false 3C 3.896,0.479 4.75,0.885 0.854,0.406 10 false 11 3.875,0.917 4.729,1.323 0.854,0.406 10 false 12 3.875,1.104 4.729,1.51 0.854,0.406 10 false 3C 3.844,1.677 4.698,2.083 0.854,0.406 10 false 3A 3.875,1.49 4.729,1.896 0.854,0.406 10 false 1 4.167,3.5 7.125,4.229 2.958,0.729 10 false Main Body ECU (Fuse Block Assembly) 1.271,0.688 3.115,1.344 1.844,0.656 10 false to Fog Light Assembly RH 2.177,1.656 4.021,2.313 1.844,0.656 10 false from Battery 1.313,1.094 3.156,1.75 1.844,0.656 10 false to Fog Light Assembly LH 4.573,1.542 5.427,1.948 0.854,0.406 10 false 3 5.271,1.531 6.125,1.938 0.854,0.406 10 false 5 4.563,1.802 5.417,2.208 0.854,0.406 10 false 1 5.271,1.802 6.125,2.208 0.854,0.406 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (FR FOG LAMP)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Body Electrical / Body / Active Test.


e.

According to the display on the GTS or Techstream, perform the Active Test.

Body Electrical / Body / Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fr fog lamp Front fog light relay ON/OFF -

OK:

Front fog light relay operates (Front fog lights come on).


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (FUSE BLOCK ASSEMBLY)

C

2.INSPECT FOG RELAY
2.INSPECT FOG RELAY
a.

Remove the FOG relay from the main body ECU (fuse block assembly).



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE FOG RELAY