Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1612/83  Lost Communication with Front Airbag Sensor RH  B1613/83  Front Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

The front airbag sensor RH circuit consists of the airbag ECU assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

DTC B1612/83 or B1613/83 is stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1612/83 Lost Communication with Front Airbag Sensor RH One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.

·

A front airbag sensor RH malfunction.

·

An airbag ECU assembly malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag ECU assembly


DTC is not output in check mode
B1613/83 Front Airbag Sensor RH Initialization Incomplete One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.

·

A front airbag sensor RH malfunction.

·

An airbag ECU assembly malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Airbag ECU assembly


DTC is not output in check mode

WIRING DIAGRAM

C279108E74
1.219,0.917 1.76,1.167 0.542,0.25 10 false SRH+ 1.24,2.083 1.656,2.292 0.417,0.208 10 false SRH- 5.594,2.063 5.979,2.24 0.385,0.177 10 false FSS- 5.594,0.896 5.99,1.094 0.396,0.198 10 false FSS+ 5.531,3.01 7.083,3.26 1.552,0.25 10 false Airbag ECU Assembly 5.573,2.833 6.031,3.031 0.458,0.198 10 false E76 0.354,2.854 0.708,3.052 0.354,0.198 10 false A25 1.688,1.969 1.917,2.156 0.229,0.188 10 false 1 3.583,1.906 3.844,2.063 0.26,0.156 10 false 2 3.563,0.729 3.792,0.885 0.229,0.156 10 false 1 1.688,0.813 1.917,1 0.229,0.188 10 false 2 3.448,0.917 3.906,1.115 0.458,0.198 10 false AE7 3.438,2.083 3.875,2.281 0.438,0.198 10 false AE7 5.323,0.792 5.583,0.948 0.26,0.156 10 false 12 5.333,1.969 5.594,2.125 0.26,0.156 10 false 13 0.323,3.021 1.906,3.198 1.583,0.177 10 false Front Airbag Sensor RH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor RH.

Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected




The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag ECU assembly and front airbag sensor RH.


b.
C334741C01
0.563,1.656 0.875,1.813 0.313,0.156 10 false *1 2.594,1.594 2.906,1.75 0.313,0.156 10 false *2
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly


Check that the connectors (on the airbag ECU assembly side and front airbag sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

The connectors are deformed or damaged

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C312964C02
2.5,0.75 2.917,1 0.417,0.25 4.458,0.75 4.875,1 0.417,0.25 5.458,1.26 5.458,1.49 false 5.375,0.833 5.094,1.396 5.094,1.396 4.927,1.396 true 5.563,0.844 5.833,1.333 5.833,1.333 5.99,1.333 true 3.313,0.958 3.115,1.552 3.115,1.552 2.917,1.552 true 3.646,0.979 3.823,1.573 3.823,1.573 4.031,1.573 true 0.302,1.229 0.615,1.385 0.313,0.156 10 false *1 1.719,1.208 2.031,1.365 0.313,0.156 10 false *2 4,0.76 4.313,0.917 0.313,0.156 10 false *3 6.719,0.771 7.031,0.927 0.313,0.156 10 false *4 5.396,1.521 5.708,1.677 0.313,0.156 10 false *5 3.417,0.271 3.729,0.427 0.313,0.156 10 false *a 5.719,0.302 6.031,0.458 0.313,0.156 10 false *b 0.458,0.813 0.771,0.969 0.313,0.156 10 false F 1.604,0.833 1.917,0.99 0.313,0.156 10 false A 0.719,1.042 1.031,1.198 0.313,0.156 10 false E 0.958,1.042 1.271,1.198 0.313,0.156 10 false D 1.073,1.042 1.385,1.198 0.313,0.156 10 false C 1.313,1.042 1.625,1.198 0.313,0.156 10 false B 2.583,0.792 3,0.99 0.417,0.198 10 false A25 4.552,0.792 4.969,0.99 0.417,0.198 10 false E76 6.042,1.26 6.5,1.479 0.458,0.219 10 false FSS+ 4.573,1.302 5.031,1.521 0.458,0.219 10 false FSS- 4.073,1.49 4.531,1.708 0.458,0.219 10 false SRH+ 2.563,1.458 3.021,1.677 0.458,0.219 10 false SRH-
*1 Front Airbag Sensor RH *2 Airbag ECU Assembly
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A25-2 (SRH+) - Body ground Ignition switch ON Below 1 V
A25-1 (SRH-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 12 (FSS+) and 13 (FSS-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-2 (SRH+) - A25-1 (SRH-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-2 (SRH+) - A25-1 (SRH-) Always 1 MΩ or higher
A25-2 (SRH+) - Body ground Always 1 MΩ or higher
A25-1 (SRH-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR RH

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK FRONT AIRBAG SENSOR RH
a.
C334740C01
0.708,1.604 1.021,1.76 0.313,0.156 10 false *1 2.448,1.573 2.76,1.729 0.313,0.156 10 false *2
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly


Connect the connectors to the airbag ECU assembly.


b.

Interchange the front airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > A/B > Clear DTCs
50002 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


f.

Turn the ignition switch off


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > A/B > Trouble Codes
50001 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Result:
Proceed to
DTC B1612/83 or B1613/83 is output
DTC B1617/84 or B1618/84 is output
DTC B1612/83, B1613/83, B1617/84 and B1618/84 are not output


HINT:

Codes other than DTC B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the front airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1612/83 or B1613/83 is output

DTC B1617/84 or B1618/84 is output

DTC B1612/83, B1613/83, B1617/84 and B1618/84 are not output

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C312965C02
2.917,0.75 3.333,1 0.417,0.25 4.667,0.75 5.083,1 0.417,0.25 5.729,1.271 5.729,1.5 false 3.927,0.781 4.198,1.229 4.198,1.229 4.396,1.229 true 3.677,0.771 3.417,1.25 3.417,1.25 3.25,1.25 true 5.833,0.865 6.115,1.354 6.115,1.354 6.313,1.354 true 5.698,0.865 5.979,1.625 5.979,1.625 6.177,1.625 true 0.604,1.146 0.917,1.302 0.313,0.156 10 false *1 2.146,1.146 2.458,1.302 0.313,0.156 10 false *2 1.146,0.625 1.458,0.781 0.313,0.156 10 false *3 1.552,0.625 1.865,0.781 0.313,0.156 10 false *4 3.76,0.229 4.073,0.385 0.313,0.156 10 false *5 5.99,0.25 6.302,0.406 0.313,0.156 10 false *6 5.667,1.531 5.979,1.688 0.313,0.156 10 false *7 3.031,0.177 3.344,0.333 0.313,0.156 10 false *a 4.771,0.188 5.083,0.344 0.313,0.156 10 false *b 0.75,0.771 1.063,0.927 0.313,0.156 10 false F 1.042,1.031 1.354,1.188 0.313,0.156 10 false E 1.281,1.031 1.594,1.188 0.313,0.156 10 false D 1.458,1.031 1.771,1.188 0.313,0.156 10 false C 1.719,1.031 2.031,1.188 0.313,0.156 10 false B 2.021,0.792 2.333,0.948 0.313,0.156 10 false A 2.99,0.792 3.406,1.052 0.417,0.26 10 false AE7 4.75,0.802 5.167,1.063 0.417,0.26 10 false E76 4.438,1.156 4.854,1.417 0.417,0.26 10 false FSS+ 2.906,1.156 3.323,1.417 0.417,0.26 10 false FSS- 6.354,1.281 6.771,1.542 0.417,0.26 10 false FSS+ 6.229,1.552 6.656,1.781 0.427,0.229 10 false FSS-
*1 Front Airbag Sensor RH *2 Airbag ECU Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AE7-1 (FSS+) - Body ground Ignition switch ON Below 1 V
AE7-2 (FSS-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 12 (FSS+) and 13 (FSS-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AE7-1 (FSS+) - AE7-2 (FSS-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AE7-1 (FSS+) - AE7-2 (FSS-) Always 1 MΩ or higher
A7E-1 (FSS+) - Body ground Always 1 MΩ or higher
AE7-2 (FSS-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE