Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2015.08
RM19Y0E _58 Vehicle Interior _003010 SUPPLEMENTAL RESTRAINT SYSTEMS _0015213 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag ECU assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

DTC B1617/84 or B1618/84 is stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1617/84 Lost Communication with Front Airbag Sensor LH One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

An airbag ECU assembly malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag ECU assembly


DTC is output in check mode
B1618/84 Front Airbag Sensor LH Initialization Incomplete One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

An airbag ECU assembly malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag ECU assembly


DTC is output in check mode

WIRING DIAGRAM

C279108E75
1.25,0.917 1.688,1.135 0.438,0.219 10 false SLH+ 1.271,2.083 1.708,2.323 0.438,0.24 10 false SLH- 5.594,2.063 5.979,2.24 0.385,0.177 10 false SL- 5.563,0.896 5.958,1.094 0.396,0.198 10 false SL+ 5.531,3.01 7.083,3.24 1.552,0.229 10 false Airbag ECU Assembly 5.542,2.833 6,3.031 0.458,0.198 10 false E76 0.323,2.854 0.677,3.052 0.354,0.198 10 false A26 1.688,1.969 1.917,2.156 0.229,0.188 10 false 1 3.563,0.719 3.823,0.875 0.26,0.156 10 false 3 3.552,1.885 3.781,2.042 0.229,0.156 10 false 4 1.688,0.813 1.917,1 0.229,0.188 10 false 2 3.448,0.917 3.906,1.115 0.458,0.198 10 false AE7 3.458,2.083 3.896,2.281 0.438,0.198 10 false AE7 5.313,0.771 5.573,0.927 0.26,0.156 10 false 14 5.313,1.958 5.573,2.115 0.26,0.156 10 false 15 0.323,3.021 1.906,3.198 1.583,0.177 10 false Front Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag ECU assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor LH.

Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected




The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag ECU assembly and front airbag sensor LH.


b.
C334741C01
0.563,1.656 0.875,1.813 0.313,0.156 10 false *1 2.594,1.594 2.906,1.75 0.313,0.156 10 false *2
*1 Front Airbag Sensor LH
*2 Airbag ECU Assembly


Check that the connectors (on the airbag ECU assembly side and front airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

The connectors are deformed or damaged

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C312966C02
2.5,0.75 2.917,1 0.417,0.25 4.417,0.75 4.833,1 0.417,0.25 5.219,1.25 5.219,1.49 false 3.313,0.979 3.188,1.354 3.188,1.354 3,1.354 true 3.667,0.979 3.76,1.354 3.76,1.354 3.938,1.354 true 5.313,0.854 5.542,1.375 5.542,1.375 5.719,1.375 true 5.177,0.865 5.438,1.583 5.438,1.583 5.615,1.583 true 0.333,1.188 0.646,1.344 0.313,0.156 10 false *1 1.729,1.167 2.042,1.323 0.313,0.156 10 false *2 3.958,0.677 4.271,0.833 0.313,0.156 10 false *3 6.667,0.708 6.979,0.865 0.313,0.156 10 false *4 5.156,1.531 5.469,1.688 0.313,0.156 10 false *5 3.396,0.292 3.708,0.448 0.313,0.156 10 false *a 5.667,0.313 5.979,0.469 0.313,0.156 10 false *b 0.438,0.823 0.75,0.979 0.313,0.156 10 false F 1.604,0.823 1.917,0.979 0.313,0.156 10 false A 0.708,1.031 1.021,1.188 0.313,0.156 10 false E 0.938,1.031 1.25,1.188 0.313,0.156 10 false D 1.073,1.031 1.385,1.188 0.313,0.156 10 false C 1.323,1.031 1.635,1.188 0.313,0.156 10 false B 2.594,0.792 3.01,1.021 0.417,0.229 10 false A26 4.51,0.792 4.927,1.021 0.417,0.229 10 false E76 2.625,1.26 3.042,1.49 0.417,0.229 10 false SLH- 4,1.281 4.417,1.51 0.417,0.229 10 false SLH+ 5.76,1.292 6.177,1.521 0.417,0.229 10 false SL+ 5.656,1.51 6.073,1.74 0.417,0.229 10 false SL-
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A26-2 (SLH+) - Body ground Ignition switch ON Below 1 V
A26-1 (SLH-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 14 (SL+) and 15 (SL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-2 (SLH+) - A26-1 (SLH-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-2 (SLH+) - A26-1 (SLH-) Always 1 MΩ or higher
A26-2 (SLH+) - Body ground Always 1 MΩ or higher
A26-1 (SLH-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR LH

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK FRONT AIRBAG SENSOR LH
a.
C334740C01
0.708,1.604 1.021,1.76 0.313,0.156 10 false *1 2.448,1.573 2.76,1.729 0.313,0.156 10 false *2
*1 Front Airbag Sensor RH
*2 Airbag ECU Assembly


Connect the connectors to the airbag ECU assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > A/B > Clear DTCs
50002 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR


f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Body Electrical > A/B > Trouble Codes
50001 587

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Result:
Proceed to
DTC B1617/84 or B1618/84 is output
DTC B1612/83 or B1613/83 is output
DTC B1612/83, B1613/83, B1617/84 and B1618/84 are not output


HINT:

Codes other than DTC B1612/83, B1613/83, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the front airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B1617/84 or B1618/84 is output

DTC B1612/83 or B1613/83 is output

DTC B1612/83, B1613/83, B1617/84 and B1618/84 are not output

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire connector from the engine room main wire.

C312967C02
2.917,0.75 3.333,1 0.417,0.25 4.667,0.75 5.083,1 0.417,0.25 3.927,0.958 4.156,1.208 4.156,1.208 4.313,1.208 true 3.688,0.948 3.458,1.219 3.458,1.219 3.281,1.219 true 5.448,1.281 5.448,1.51 false 5.563,0.875 5.854,1.302 5.854,1.302 6.01,1.302 true 5.406,0.885 5.729,1.51 5.729,1.51 5.885,1.51 true 0.615,1.156 0.927,1.313 0.313,0.156 10 false *1 2.125,1.156 2.438,1.313 0.313,0.156 10 false *2 1.146,0.625 1.458,0.781 0.313,0.156 10 false *3 1.552,0.625 1.865,0.781 0.313,0.156 10 false *4 3.74,0.188 4.052,0.344 0.313,0.156 10 false *5 5.875,0.188 6.188,0.344 0.313,0.156 10 false *6 5.385,1.552 5.698,1.708 0.313,0.156 10 false *7 3.042,0.104 3.354,0.26 0.313,0.156 10 false *a 4.792,0.104 5.104,0.26 0.313,0.156 10 false *b 0.729,0.781 1.042,0.938 0.313,0.156 10 false F 1.031,1.01 1.344,1.167 0.313,0.156 10 false E 1.281,1.01 1.594,1.167 0.313,0.156 10 false D 1.448,1.01 1.76,1.167 0.313,0.156 10 false C 1.708,1.01 2.021,1.167 0.313,0.156 10 false B 2.031,0.802 2.344,0.958 0.313,0.156 10 false A 3,0.792 3.406,1.042 0.406,0.25 10 false AE7 4.75,0.792 5.156,1.042 0.406,0.25 10 false E76 4.365,1.125 4.771,1.375 0.406,0.25 10 false SL+ 3,1.125 3.406,1.375 0.406,0.25 10 false SL- 5.917,1.438 6.26,1.708 0.344,0.271 10 false SL- 6.042,1.219 6.385,1.49 0.344,0.271 10 false SL+
*1 Front Airbag Sensor LH *2 Airbag ECU Assembly
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AE7-3 (SL+) - Body ground Ignition switch ON Below 1 V
AE7-4 (SL-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 14 (SL+) and 15 (SL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AE7-3 (SL+) - AE7-4 (SL-) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AE7-3 (SL+) - AE7-4 (SL-) Always 1 MΩ or higher
AE7-3 (SL+) - Body ground Always 1 MΩ or higher
AE7-4 (SL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE