Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0010  IN. Oil Control Valve System Open/Short Malfuction  


DESCRIPTION

A363309E01
2.135,0.813 1.813,0.552 false 3.042,0.531 2.667,0.823 false 1.354,1.208 1,1.063 false 1.542,1.573 1.01,1.948 true 1.479,2.313 1.875,2.208 false 2.031,2.594 2.417,2.24 false 2.938,2.208 3.208,2.292 false 3.927,2.552 3.448,1.573 true 5.635,2.313 4.625,1.938 true 5.75,1.719 4.844,1.563 true 0.083,0.073 2.896,0.438 2.813,0.365 10 false Camshaft Timing Oil Control Valve Assembly: 0.771,0.438 1.802,0.76 1.031,0.323 10 false (Advanced Side) 3.083,0.448 4.104,0.708 1.021,0.26 10 false (Retarded Side) 0.563,0.958 1.021,1.24 0.458,0.281 10 false Sleeve 0.583,1.844 1.021,2.094 0.438,0.25 10 false Spring 1.135,2.219 1.51,2.49 0.375,0.271 10 false Drain 1.25,2.51 2.073,2.74 0.823,0.229 10 false Oil Pressure 3.25,2.208 3.635,2.51 0.385,0.302 10 false Drain 3.969,2.469 4.719,2.75 0.75,0.281 10 false Spool Valve 5.792,1.646 6.302,1.906 0.51,0.26 10 false Plunger 5.688,2.229 5.979,2.458 0.292,0.229 10 false Coil

This circuit operates the spool valve by means of the duty signal from the ECM so as to switch the oil passages to the advanced side or retarded side to activate the VVT controller (camshaft timing sprocket assembly). In this way, optimum valve timing is maintained.

When the engine is stopped, the camshaft timing oil control valve is set to the most retarded position.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 IN. Oil Control Valve System Open/Short Malfuction Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit for 1 seconds or more
(1 trip detection logic)
·

Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on.

6.

Wait 10 seconds or more.

7.

Enter the following menus: Powertrain / EFI / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A266584E06
0.281,1.99 3.031,2.344 2.75,0.354 10 false Camshaft Timing Oil Control Valve Assembly(for Intake Camshaft) 0.281,1.802 0.854,2.156 0.573,0.354 10 false C21 1.594,0.719 1.896,1.01 0.302,0.292 10 false 1 1.594,1.354 1.875,1.677 0.281,0.323 10 false 2 5.51,2.281 5.875,2.615 0.365,0.333 10 false ECM 5.521,2.115 6.052,2.469 0.531,0.354 10 false C50 5.125,1.333 5.792,1.625 0.667,0.292 10 false OCV- 4.875,1.333 5.188,1.635 0.313,0.302 10 false 11 4.865,0.719 5.156,0.99 0.292,0.271 10 false 10 5.115,0.719 5.698,1.063 0.583,0.344 10 false OCV+

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (P0010)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear DTCs after recording the freeze frame data and DTCs.


e.

Start the engine.


f.

Allow the engine to idle and check for DTCs.


g.

Enter the following menus: Powertrain / EFI / Trouble Codes.


h.

Read DTCs.


Result:
Result Proceed to
DTC P0010 is output A
DTC is not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake camshaft).

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C21-1 - C50-10 (OCV+) Always Below 1 Ω
C21-2 - C50-11 (OCV-) Always Below 1 Ω
C21-1 or C50-10 (OCV+) - Body ground Always 10 kΩ or higher
C21-2 or C50-11 (OCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR