Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0120  Throttle Position Sensor (Main) Open  P0121  Throttle Position Sensor Range Malfunction  P0122  Throttle Position Sensor (Main) Open/Low  P0123  Throttle Position Sensor (Main) Open/High  P0220  Throttle Position Sensor (Sub) Open  P0222  Throttle Position Sensor (Sub) Open/Low  P0223  Throttle Position Sensor (Sub) Open/High  P2135  Throttle Position Sensor Main/Sub Voltage Correlation  


DESCRIPTION

HINT:

These DTCs relate to the throttle position sensor.


The throttle position sensor is mounted on the throttle body with motor assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, VTA1 and VTA2 each of which transmits a signal. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

A293043E06
4.188,1.063 4.385,0.583 4.385,0.583 4.542,0.583 false 5.74,1.51 5.51,0.281 5.51,0.281 5.229,0.281 false 5.323,1.875 5.802,2.323 false 4.979,2.229 5.313,2.531 false 1.042,2.604 0.865,1.792 0.865,1.792 0.771,1.792 true 1.49,1.219 1.063,2.188 true 0.969,2.958 0.583,3.563 true 1.073,3.344 1.552,3.75 true 4.677,1.469 4.896,1.656 false 1.573,1.052 2.49,1.25 0.917,0.198 10 Magnet 0.25,1.708 1.167,1.906 0.917,0.198 10 IC No. 1 0.323,3.656 1.24,3.854 0.917,0.198 10 IC No. 2 1.594,3.74 2.51,3.938 0.917,0.198 10 Magnet 0.104,4.115 1.979,4.406 1.875,0.292 10 Throttle Position Sensor 0.146,4.458 2.021,4.75 1.875,0.292 10 Note: 0.146,4.719 3.354,5.344 3.208,0.625 10 The throttle valve opening angle transmitted through sensor terminal VTA1 is expressed as a percentage. 0.146,5.51 3.344,5.729 3.198,0.219 10 Between 10% and 22%: Throttle valve fully closed 0.135,5.813 3.333,6.031 3.198,0.219 10 Between 64% and 96%: Throttle valve fully open 0.146,6.135 3.344,6.354 3.198,0.219 10 Approximately 18.2%: Fail safe angle (5.5°) 3.531,0.188 5.271,0.479 1.74,0.292 10 Line indicating VTA2 x 0.8 2.5,0.677 4.24,0.969 1.74,0.292 10 Sensor Output Voltage (V) 4.604,0.51 5.604,0.865 1,0.354 10 Fail-safe Angle 5.385,2.531 5.781,2.938 0.396,0.406 10 VTA1 4.396,3.563 6.594,3.896 2.198,0.333 10 Throttle Valve Opening Angle (°) 3.906,4.021 6.042,4.24 2.135,0.219 10 *: During fail-safe control 3.719,4.76 5.917,5.094 2.198,0.333 10 Characteristics of sensor output: 3.75,5.042 7.156,5.354 3.406,0.313 10 VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V 5.823,2.375 6.427,2.75 0.604,0.375 10 1.11 V 4.281,1.365 4.677,1.771 0.396,0.406 10 VTA2 3.75,0.99 4.01,1.396 0.26,0.406 10 5.0 3.667,1.188 4,1.594 0.333,0.406 10 4.65 3.594,1.917 4.25,2.156 0.656,0.24 10 2.525* 3.688,2.063 4.021,2.469 0.333,0.406 10 2.25 3.625,2.438 4.208,2.656 0.583,0.219 10 0.91* 3.656,2.604 3.99,3.01 0.333,0.406 10 0.69 4.125,2.865 4.458,3.271 0.333,0.406 10 5.5 3.979,3.271 4.313,3.677 0.333,0.406 10 0 6.271,3.292 6.604,3.698 0.333,0.406 10 86 1.688,2.771 2.083,3.177 0.396,0.406 10 VTA2 1.677,2.385 2.073,2.792 0.396,0.406 10 VTA1 1.677,2.021 2.26,2.375 0.583,0.354 10 VCTA 1.708,3.125 2.104,3.531 0.396,0.406 10 ETA 4.698,3.188 5.719,3.406 1.021,0.219 10 Usable Range 2.417,4.073 3.333,4.271 0.917,0.198 10 ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0120 Throttle Position Sensor (Main) Open The output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored
P0121 Throttle Position Sensor Range Malfunction The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or higher than 1.6 V for 2 seconds (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


Comes on DTC stored
P0122 Throttle Position Sensor (Main) Open/Low The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA1 circuit

·

Open in VCTA circuit

·

ECM


Comes on DTC stored
P0123 Throttle Position Sensor (Main) Open/High The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA1 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA1 circuits

·

ECM


Comes on DTC stored
P0220 Throttle Position Sensor (Sub) Open The output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored
P0222 Throttle Position Sensor (Sub) Open/Low The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA2 circuit

·

Open in VCTA circuit

·

ECM


Comes on DTC stored
P0223 Throttle Position Sensor (Sub) Open/High The output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA2 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA2 circuits

·

ECM


Comes on DTC stored
P2135 Throttle Position Sensor Main/Sub Voltage Correlation Either of the following conditions is met (1 trip detection logic):
(a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) The output voltage of VTA1 is 0.2 V or less, and VTA2 is 1.75 V or less for 0.4 seconds or more.
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored

HINT:
·

When any of these DTCs are output, check the throttle valve opening angle using the GTS or Techstream. Enter the following menus: Powertrain / EFI / Data List / Main throttle sensor voltage and Sub throttle sensor voltage.

·

Main throttle sensor voltage is the VTA1 signal, and Sub throttle sensor voltage is the VTA2 signal.

Reference (Normal Condition):
GTS or Techstream Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Main throttle sensor voltage 0.5 to 1.1 V 3.2 to 4.8 V
Sub throttle sensor voltage 2.1 to 3.1 V 4.6 to 4.98 V




CONFIRMATION DRIVING PATTERN

A198824E34
3.688,1.396 3.323,0.406 3.323,0.406 3.552,0.406 false 2.635,2 2.375,1.208 2.375,1.208 2.542,1.208 false 4.927,2 5.271,1.104 5.271,1.104 5.375,1.104 false 1.229,1.875 1.604,2.042 0.375,0.167 10 Idling 0.417,2.146 1.615,2.292 1.198,0.146 10 Ignition Switch ON 2.115,2.01 2.354,2.198 0.24,0.188 10 [A] 3.844,1.76 4.083,1.948 0.24,0.188 10 [B] 5.438,1.031 6.073,1.177 0.635,0.146 10 Released 3.625,0.313 4.354,0.458 0.729,0.146 10 Depressed 4.406,2.604 5.104,2.948 0.698,0.344 10 2 seconds or more 4.708,1.719 4.948,1.927 0.24,0.208 10 [C] 5.031,2.969 5.313,3.167 0.281,0.198 10 [D] 2.583,1.135 3.219,1.281 0.635,0.146 10 Released

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Start the engine.

7.

With the vehicle stationary, fully depress and release the accelerator pedal [B].

8.

Idle the engine for 2 seconds or more [C].

9.

Enter the following menus: Powertrain / EFI / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 5.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue operating at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A362206E02
1.823,0.646 2.135,0.844 0.313,0.198 10 false VC 2.177,0.521 2.333,0.719 0.156,0.198 10 false 5 1.688,1.208 2.115,1.406 0.427,0.198 10 false VTA1 2.188,1.094 2.344,1.292 0.156,0.198 10 false 6 1.698,1.802 2.094,2 0.396,0.198 10 false VTA2 2.198,1.677 2.354,1.875 0.156,0.198 10 false 4 1.844,2.375 2.063,2.563 0.219,0.188 10 false E2 2.188,2.271 2.344,2.469 0.156,0.198 10 false 3 0.292,2.885 0.594,3.063 0.302,0.177 10 false C47 0.292,3.063 2.875,3.542 2.583,0.479 10 false Throttle Position Sensor (Built into Throttle Body with Motor Assembly) 4.906,0.542 5.135,0.74 0.229,0.198 10 false 55 5.167,0.542 5.594,0.75 0.427,0.208 10 false VCTA 4.896,1.104 5.146,1.302 0.25,0.198 10 false 33 5.167,1.104 5.604,1.302 0.438,0.198 10 false VTHO 4.906,1.708 5.135,1.906 0.229,0.198 10 false 77 5.167,1.698 5.573,1.896 0.406,0.198 10 false VTA2 4.906,2.271 5.104,2.469 0.198,0.198 10 false 99 5.177,2.271 5.49,2.479 0.313,0.208 10 false ETA 5.281,3.115 5.615,3.323 0.333,0.208 10 false C50 5.594,3.115 5.979,3.302 0.385,0.188 10 false ECM 3.656,2.688 3.813,2.885 0.156,0.198 10 false * 3.656,3.302 4.542,3.552 0.885,0.25 10 false *:Shielded

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS OR TECHSTREAM (THROTTLE POSITION SENSOR)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / Main throttle sensor voltage and Sub throttle sensor voltage.


e.

Read the values displayed on the GTS or Techstream.


Result:
When Accelerator Pedal Fully Released When Accelerator Pedal Fully Depressed Trouble Area Proceed to
Throttle Position No. 1 (VTA1) Throttle Position No. 2 (VTA2) Throttle Position No. 1 (VTA1) Throttle Position No. 2 (VTA2)
0 to 0.2 V 0 to 1.75 V 0 to 0.2 V 0 to 1.75 V VCTA circuit open A
4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V ETA circuit open
0 to 0.2 V, or 4.5 to 4.98 V 2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V, or 4.5 to 4.98 V 2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or ground short
0.6 to 1.4 V
(Fail-safe)
0 to 1.75 V, or 4.8 to 4.98 V 0.6 to 1.4 V
(Fail-safe)
0 to 1.75 V, or 4.8 to 4.98 V VTA2 circuit open or ground short
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 4.98 V
(Not fail-safe)
Throttle position sensor circuit normal B


HINT:
·

DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

Characteristic Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Main throttle sensor voltage

VTA2: Sub throttle sensor voltage


·

If DTC P0121 is output, proceed to "Check Harness And Connector (Throttle Position Sensor - ECM)".




A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C47-5 (VC) - C50-55 (VCTA) Always Below 1 Ω
C47-6 (VTA1) - C50-33 (VTHO) Always Below 1 Ω
C47-4 (VTA2) - C50-77 (VTA2) Always Below 1 Ω
C47-3 (E2) - C50-99 (ETA) Always Below 1 Ω
C47-5 (VC) or C50-55 (VCTA) - Body ground Always 10 kΩ or higher
C47-6 (VTA1) or C50-33 (VTHO) - Body ground Always 10 kΩ or higher
C47-4 (VTA2) or C50-77 (VTA2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
a.
A361951C01
0.167,1.917 0.583,2.167 0.417,0.25 1.552,2.083 1.333,2.656 true 2.031,2.083 2.25,2.677 true 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 0.25,1.958 0.635,2.167 0.385,0.208 10 false C47 1.24,2.698 1.625,2.906 0.385,0.208 10 false E2 2.188,2.698 2.573,2.906 0.385,0.208 10 false VC
*a Front view of wire harness connector
(to Throttle Body with Motor Assembly)


Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C47-5 (VC) - C47-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Start the engin.


h.

Drive the vehicle in accordance with the driving pattern.


i.

Enter the following menus: Powertrain / EFI / Trouble Codes.


j.

Read the DTCs.


Result:
Result Proceed to
DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 are output A
DTC is not output B



A

B

END