The crankshaft position sensor system consists of a crankshaft angle sensor plate and Magneto Resistance Element (MRE) type sensor. The crankshaft angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0335 | Crankshaft Position Sensor "A" Circuit | Either of the following conditions is met (1 trip detection logic):
·
No crankshaft position sensor signal to the ECM while cranking. ·
No crankshaft position sensor signal to the ECM while engine running. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
Crankshaft (crankshaft angle sensor plate) ·
ECM |
Comes on | DTC stored |
| P0337 | Crankshaft Position Sensor "A" Circuit Low Input | Output voltage of crankshaft position sensor is less than 0.3 V for 0.43 seconds or more (1 trip detection logic). | ·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
ECM |
Comes on | DTC stored |
| P0338 | Crankshaft Position Sensor "A" Circuit High Input | Output voltage of crankshaft position sensor is higher than 4.7 V for 0.43 seconds or more (1 trip detection logic). | ·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
ECM |
Comes on | DTC stored |
| P0339 | Crank Angle Sensor Signal Flash Open | Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or more. (b) Starter signal is off. (c) 3 seconds or more have elapsed since the starter signal switched from on to off. |
·
Open or short in crankshaft position sensor circuit ·
Crankshaft position sensor ·
Crankshaft (crankshaft angle sensor plate) ·
ECM |
Does not come on | DTC stored |
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
| ECM Terminal Name | Between N and EN |
| Tester Range | 2 V/DIV., 5 ms./DIV. |
| Condition | Idling with warm engine |
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON and turn the GTS or Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS or Techstream on.
Start the engine.
Idle the engine for 20 seconds or more.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, the system is normal.
If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
The Engine revolution speed can be checked by using the GTS or Techstream. To perform the check, follow the procedures below:
Connect the GTS or Techstream to the DLC3.
Start the engine.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Data List / Engine revolution speed.
The Engine revolution speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the Engine revolution speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Enter the following menus: Powertrain / EFI / Data List / Engine revolution speed.
Start the engine.
Read the values displayed on the GTS or Techstream while the engine is running.
Correct values are displayed.
To check the Engine revolution speed change, display the graph on the GTS or Techstream.
If the engine does not start, check the Engine revolution speed while cranking.
If the Engine revolution speed indicated on the GTS or Techstream remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Crankshaft Position Sensor) |
Disconnect the crankshaft position sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C38-3 (VCN) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C38-1 (N) - C50-79 (N) | Always | Below 1 Ω |
| C38-2 (EN) - C50-101 (EN) | Always | Below 1 Ω |
| C38-1 (N) or C50-79 (N) - Body ground | Always | 10 kΩ or higher |
| C38-2 (EN) or C50-101 (EN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | OK |
| *b | NG |
| *c | Clearance |
Check the crankshaft position sensor installation condition.
Crankshaft position sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the teeth of the crankshaft angle sensor plate.
Crankshaft angle sensor plate does not have any cranks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the crankshaft position sensor.
Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS or Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the GTS or Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS or Techstream on.
Drive the vehicle in accordance with the driving pattern.
Enter the following menus: Powertrain / EFI / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0335, P0337, P0338 and/or P0339 are output | B |
A
B
Disconnect the crankshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C38-3 (VCN) - C50-57 (VCN) | Always | Below 1 Ω |
| C38-3 (VCN) or C50-57 (VCN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG