Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0443  Evaporator Purge VSV System Malfunction  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the No. 1 vacuum switching valve assembly so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0443 Evaporator Purge VSV System Malfunction Both of the following conditions (a) and (b) are met (1 trip detection logic)

(a) The target control value and actual control value do not match for 10 seconds or more.


(b) The target control value and actual control value do not match for 80 times or more.


·

Open or short in No. 1 vacuum switching valve assembly circuit

·

No. 1 vacuum switching valve assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A325627E01
5.167,3.094 5.427,3.333 0.26,0.24 10 false [D] 1.354,2.667 2.188,3.042 0.833,0.375 10 false Warming up 0.521,2.177 0.979,2.5 0.458,0.323 10 false Idling 0.042,1.563 1.385,1.938 1.344,0.375 10 false 40 to 60 km/h 2.385,2.688 3.615,3.083 1.229,0.396 10 false 15 minutes or more 4.292,2.688 4.99,3.146 0.698,0.458 10 false 10 minutes or more 6.635,2.531 7.125,2.917 0.49,0.385 10 false Time 1.563,2.073 1.979,2.313 0.417,0.24 10 false [A] 2.854,2.083 3.354,2.333 0.5,0.25 10 false [B] 4.667,1.448 5.115,1.792 0.448,0.344 10 false [C] 0.354,0.646 0.833,1.042 0.479,0.396 10 false Vehicle Speed

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on.

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


7.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


8.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / EFI / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




WIRING DIAGRAM

A360377E05
0.615,3.906 1.208,4.167 0.594,0.26 10 false Battery 0.458,3.177 1.104,3.406 0.646,0.229 10 false FL MAIN 0.448,2.469 0.823,2.688 0.375,0.219 10 false EFI 1.5,1.885 2.927,2.25 1.427,0.365 10 false No. 1 Integration Relay 1.823,1.5 2.563,1.781 0.74,0.281 10 false EFI-MAIN 0.76,0.604 1.073,0.802 0.313,0.198 10 false 1F 0.76,0.417 0.938,0.615 0.177,0.198 10 false 17 3.208,0.594 3.521,0.792 0.313,0.198 10 false 1J 3.219,0.427 3.375,0.625 0.156,0.198 10 false 3 3.208,1.135 3.521,1.333 0.313,0.198 10 false 1F 3.219,0.948 3.375,1.146 0.156,0.198 10 false 5 4.281,0.5 4.438,0.698 0.156,0.198 10 false 2 5.063,0.49 5.219,0.688 0.156,0.198 10 false 1 4.042,0.917 4.5,1.115 0.458,0.198 10 false C20 4.333,0.917 5.833,1.323 1.5,0.406 10 false No. 1 Vacuum Switching Valve Assembly 5.813,0.594 6.271,0.792 0.458,0.198 10 false C50 5.854,0.406 6.167,0.604 0.313,0.198 10 false 87 6.135,0.604 6.594,0.802 0.458,0.198 10 false PRG 5.844,2.25 6.156,2.448 0.313,0.198 10 false 28 5.813,2.427 6.271,2.625 0.458,0.198 10 false A24 6.125,2.427 6.583,2.625 0.458,0.198 10 false MRO 5.896,2.802 6.052,3 0.156,0.198 10 false 4 5.813,2.99 6.271,3.188 0.458,0.198 10 false C50 6.125,2.99 6.583,3.188 0.458,0.198 10 false E01 6.375,3.49 6.833,3.688 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (PURGE VSV)
a.
A359887C01
0.406,0.667 0.719,0.865 0.313,0.198 10 false *a 1.979,0.677 2.292,0.875 0.313,0.198 10 false *b
*a VSV is on
*b VSV is off


Disconnect the fuel vapor feed hose (charcoal canister side) of the No. 1 vacuum switching valve assembly.


b.

Connect the GTS or Techstream to the DLC3.


c.

Start the engine.


d.

Turn the GTS or Techstream on.


e.

Enter the following menus: Powertrain / EFI / Active Test / Purge VSV.


f.

When the No. 1 vacuum switching valve assembly is operated using the GTS or Techstream, check whether the port of the No. 1 vacuum switching valve assembly applies suction your finger.

Standard:
GTS or Techstream Operation Specified Condition
100% No. 1 vacuum switching valve assembly port applies suction to finger
0% No. 1 vacuum switching valve assembly port applies no suction to finger



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 1 VACUUM SWITCHING VALVE ASSEMBLY
2.INSPECT NO. 1 VACUUM SWITCHING VALVE ASSEMBLY
a.

Inspect the No. 1 vacuum switching valve assembly.

Click hereEngine / Hybrid System>2NR-VE EMISSION CONTROL>PURGE VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 VACUUM SWITCHING VALVE ASSEMBLY)

NG

REPLACE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 VACUUM SWITCHING VALVE ASSEMBLY)
a.
A361084C01
0.49,2.208 0.906,2.5 0.417,0.292 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.563,2.281 1.021,2.479 0.458,0.198 10 false C20
*a Front view of wire harness connector
(to No. 1 Vacuum Switching Valve Assembly)


Disconnect the No. 1 vacuum switching valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C20-2 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 VACUUM SWITCHING VALVE ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE ASSEMBLY - ECM)
a.

Disconnect the No. 1 vacuum switching valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-1 - C50-87 (PRG) Always Below 1 Ω
C20-1 or C50-87 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR