Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P0604  Random Access Memory Error  P0606  CPU Error  P060A  Internal Control Module Monitoring Processor Performance  P060B  Internal Control Module A/D Processing Performance  P060D  Internal Control Module Accelerator Pedal Position Performance  P060E  Internal Control Module Throttle Position Performance  P062F  Internal Control Module EEPROM Error  P0657  Actuator Supply Voltage Circuit Open  


DESCRIPTION

The ECM continuously monitors its internal memory status. This self-check ensures that the ECM is functioning properly. The ECM memory status is diagnosed by internal mirroring of the main CPU and sub CPU to detect Random Access Memory (RAM) errors. If outputs from these CPUs are different and deviate from the standard, the ECM will illuminate the MIL and store this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0604 Random Access Memory Error ECM RAM error (1 trip detection logic). ECM Comes on DTC stored
P0606 CPU Error An ECM main CPU error (1 trip detection logic). ECM Comes on DTC stored
P060A Internal Control Module Monitoring Processor Performance A CPU reset is performed after one of the following conditions is met (1 trip detection logic):
·

There is an ECM main CPU error.

·

There is an ECM sub CPU error.

·

There is an electronic throttle monitoring CPU error.


ECM Comes on DTC stored
P060B Internal Control Module A/D Processing Performance An ECM main CPU communication error (1 trip detection logic). ECM Comes on DTC stored
P060D Internal Control Module Accelerator Pedal Position Performance Either of the following conditions is met (1 trip detection logic):
·

There is an ECM main CPU error.

·

There is an ECM sub CPU error.


ECM Comes on DTC stored
P060E Internal Control Module Throttle Position Performance Either of the following conditions is met (1 trip detection logic):
·

There is an ECM main CPU error.

·

There is an ECM sub CPU error.


ECM Comes on DTC stored
P062F Internal Control Module EEPROM Error An ECM internal error (EEPROM) (1 trip detection logic). ECM Does not come on DTC stored
P0657 Actuator Supply Voltage Circuit Open Throttle actuator power supply error (1 trip detection logic). ECM Comes on DTC stored

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the GTS or Techstream off.

5.

Turn the ignition switch off.

6.

Disconnect the GTS or Techstream.

7.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

8.

Connect the cable to the negative (-) battery terminal.

9.

Connect the GTS or Techstream to the DLC3.

10.

Turn the ignition switch to ON and turn the GTS or Techstream on.

11.

Wait 16 seconds or more.

12.

Enter the following menus: Powertrain / EFI / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS (DTC P0604)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS or Techstream on.


c.

Clear the DTCs.


d.

Turn the GTS or Techstream off.


e.

Turn the ignition switch off.


f.

Disconnect the GTS or Techstream.


g.

Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.


h.

Connect the cable to the negative (-) battery terminal.


i.

Connect the GTS or Techstream to the DLC3.


j.

Turn the ignition switch to ON and turn the GTS or Techstream on.


k.

Wait for 16 seconds or more.


l.

Enter the following menus: Powertrain / EFI / Trouble Codes.


m.

Read the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC P0604, P0606, P060A, P060B, P060D or P060E is output B
DTC P060B and P0327, P0328 are output C



A

B

C