Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P2121  Accelerator Pedal Position Sensor Range/Performance  


DESCRIPTION

Refer to DTC P2120.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>P2120

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2121 Accelerator Pedal Position Sensor Range/Performance Either of following conditions (a) or (b) met for 0.5 seconds (1 trip detection logic):
(a) Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position)
(b) Difference between VPA and VPA2 is greater than or equal to the specified value.
·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A256657E14
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.448 5.115,1.802 5.115,1.802 5.26,1.802 false 2.208,2.448 2.438,2.104 2.438,2.104 2.542,2.104 false 0.125,0.094 1.75,0.333 1.625,0.24 10 Accelerator Pedal State 0.896,0.458 1.698,0.708 0.802,0.25 10 Depressed 0.99,0.927 1.708,1.167 0.719,0.24 10 Released 0.427,2.406 1.667,2.667 1.24,0.26 10 Ignition Switch ON 2.115,2.49 2.333,2.75 0.219,0.26 10 [A] 4.396,3.406 4.646,3.635 0.25,0.229 10 [C] 5.313,1.729 6.063,1.979 0.75,0.25 10 Released 2.375,3.052 3.167,3.333 0.792,0.281 10 5 seconds 2.99,1.219 3.823,1.469 0.833,0.25 10 Depressed 3.865,3.042 4.083,3.25 0.219,0.208 10 [B] 2.594,2.031 3.25,2.25 0.656,0.219 10 Released

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS or Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS or Techstream on [A].

6.

Wait for 5 seconds after turning the ignition switch to ON.

7.

Operate the accelerator pedal in accordance with the following procedure [B].

1.

Enter the following menus: Powertrain / EFI / Data List / Main accelerator position, and Sub accelerator position.

2.

Slowly depress the accelerator pedal until Main accelerator position is approximately 30% and Sub accelerator position is approximately 46%, then slowly release the accelerator pedal.


8.

Enter the following menus: Powertrain / EFI / Trouble Codes [C].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




FAIL-SAFE

The accelerator pedal position sensor has 2 (main and sub) sensor circuits. If a malfunction occurs in either of the sensor circuits, the ECM detects the abnormal signal voltage difference between the 2 sensor circuits and switches to fail-safe mode. In fail-safe mode, the functioning circuit is used to calculate the accelerator pedal opening angle to allow the vehicle to continue driving. If both circuits malfunction, the ECM regards the opening angle of the accelerator pedal as being fully closed. In this case, the throttle valve remains closed as if the engine is idling.

If a pass condition is detected and then the ignition switch is turned off, the fail-safe operation stops and the system returns to normal.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.

HINT:

If any DTCs other than P2121 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC P2121 is output A
DTC P2121 and other DTCs are output B



A

2.READ VALUE USING GTS OR TECHSTREAM (MAIN ACCELERATOR SENSOR VOLTAGE AND SUB ACCELERATOR SENSOR VOLTAGE)

B

2.READ VALUE USING GTS OR TECHSTREAM (MAIN ACCELERATOR SENSOR VOLTAGE AND SUB ACCELERATOR SENSOR VOLTAGE)
a.
A208621C05
0.719,1.75 1,1.969 0.281,0.219 10 *a 2.646,1.74 2.927,1.979 0.281,0.24 10 *b
*a Fully Depressed
*b Fully Released


Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Data List / Main accelerator sensor voltage and Sub accelerator sensor voltage.


e.

Read the values displayed on the GTS or Techstream.

Standard Voltage:
Accelerator Pedal Operation Main accelerator sensor voltage Sub accelerator sensor voltage
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V



Result:
Proceed to
OK
NG



OK

NG

3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
3.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY
a.

Replace the accelerator pedal sensor assembly.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the GTS or Techstream on.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / EFI / Trouble Codes.


i.

Read the DTCs.


Result:
Result Proceed to
DTC P2121 is output A
DTC is not output B



A

B

END